AT933Rx/ML Specifications†, Dimensions | Audio-Technica AT933RX/ML

AT933Rx/ML Specifications†

AT933Rx/ML

Polar Pattern

Element	Fixed-charge back plate
	permanently polarized condenser
Polar Pattern	MicroLine®
Frequency Response	30-20,000 Hz
Low-frequency Roll-off	150 Hz, 6 dB/octave
Open Circuit Sensitivity	– 36 dB (15.8 mV) re 1V at 1 Pa*
Impedance	200 ohms (1000 ohms without power module)
Maximum Input Sound Level	131 dB SPL, 1 kHz at 1% T.H.D.
Dynamic Range (Typical)	105 dB, 1 kHz at Max SPL
Signal-to-noise Ratio1	68 dB, 1 kHz at 1 Pa*
Switch	Flat response, low-roll-off (recessed)
Phantom Power Requirements	9-52V DC, 2 mA typical
Weight	0.7 oz (20 grams)
Microphone	0.7 oz (20 grams)

330

300

270

240

210

120

150

Power Module	2.1 oz (60 grams)
Dimensions	5.61" (142.4 mm) long, 0.31" (8.0 mm) head diameter
Microphone	5.61" (142.4 mm) long, 0.31" (8.0 mm) head diameter
Power Module	3.58" (91.0 mm) long, 0.83" (21.0 mm) diameter
Output Connector (Power Module)	Integral 3-pin XLRM-type
Cable	50' (15.2 m) long (permanently attached to microphone),
	0.13" (3.2 mm) diameter, 2-conductor, shielded cable;
	free end attaches to screw terminals in power module
Accessories Furnished (AT933Rx/ML)	AT8138 MicroLine foam windscreen;
	AT8452 MicroLine hanger
(AT933RWx/ML)	AT8138WH MicroLine foam windscreen;
	AT8452WH MicroLine hanger
(Both)	AT8533x power module
Optional Interchangeable	AT853C-ELE cardioid (120°)
Elements2	AT853H-ELE hypercardioid (100°)
	AT853O-ELE omnidirectional (360°)
	AT853SC-ELE subcardioid (170°)
	†In the interest of standards development, A.T.U.S. offers full details
	on its test methods to other industry professionals on request.
	* 1 Pascal = 10 dynes/cm2 = 10 microbars = 94 dB SPL
	1 Typical, A-weighted, using Audio Precision System One.
	2 These elements require a P12024 element adapter.

Dimensions

3.58"

15.2 m

91.0 mm

0.31"

5.61"

0.13"

0.83"

8.0 mm

142.4 mm

3.2 mm

21.0 mm

One-Year Limited Warranty

Audio -Technica microphones and accessories purchased in the U.S.A. are warranted for one year from date of purchase by Audio-Technica U.S., Inc. (A.T.U.S.) to be free of defects in materials and workmanship. In event of such defect, product will be repaired promptly without charge or, at our option, replaced with a new product of equal or superior value if delivered to A.T.U.S. or an Authorized Service Center, prepaid, together with the sales slip or other proof of purchase date. Prior approval from A.T.U.S. is required for return. This warranty excludes defects due to normal wear, abuse, shipping damage, or failure to use product in accordance with instructions. This warranty is void in the event of unauthorized repair or modification.

For return approval and shipping information, contact the Service Department, Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224.

Except to the extent precluded by applicable state law, A.T.U.S. will have no liability for any consequential, incidental, or special damages; any warranty of merchantability or fitness for particular purpose expires when this warranty expires.

This warranty gives you specific legal rights, and you may have other rights which vary from state to state.

Outside the U.S.A., please contact your local dealer for warranty details.

180

SCALE IS 5 DECIBELS PER DIVISION

LEGEND

200Hz

1kHz

5kHz

8kHz

Architects and Engineers Specifications

The microphone shall be a fixed-charge condenser with a MicroLine® polar pattern and a frequency response of 30 Hz to 20,000 Hz. It shall be capable of accepting optional interchange- able elements for additional polar patterns. It shall operate from an external 9V to 52V DC phantom power source. Nominal open-circuit output voltage with the included power module shall be 15.8 mV at 1 kHz, 1 Pascal. Output shall be low impedance balanced (200 ohms).

The microphone shall have a permanently- attached 50' (15.2 m) miniature cable with a pigtail output. The pigtail output shall connect to a power module via internal solderless screw terminals. The power module shall include a switch for low-frequency roll-off and shall terminate in a 3-pin XLRM-type output connector.

The microphone shall be mountable in an included steel hanger that allows permanent overhead installation for pickup of dialogue, orchestras and choirs. The microphone shall be 5.61" (142.4 mm) long with a head diameter of 0.31" (8.0 mm). The microphone weight shall be 0.7 oz (20 grams) without cable. The microphone case, cable and steel hanger shall be black [white].

The Audio-Technica AT933Rx/ML [AT933RWx/ML] is specified.

Audio -Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224

Audio-Technica Limited, Old Lane, Leeds LS11 8AG England