Heatiator T4800 manual Marking the Exit Point of the Roof, Cutting out the Hole in the Roof

Page 16

T4800 INSTALLATION INSTRUCTIONS

9. Marking the Exit Point of the Roof

Locate the point where the chimney will exit the roof by plumbing down to the center of the chimney. Drive a nail up through the roof to mark the center. See Figure 14.

10.Cutting out the Hole in the Roof

Measure to either side of the nail and mark the 17” x 17” or 17” x 26” opening required. This is measured on the horizontal; actual length may be larger depending on the pitch of the roof. Cut out and frame the opening. See Chapter 25 of the Uniform

Building Code for Roof Framing Details.

Be sure to maintain a 2” minimum air space between the chimney section and the roof.

11.Assembling the Chimney Sections Through the Roof

Continue to add chimney sections through the roof opening, maintaining at least a 2” air space.

12.Installing the Roof Flashing

If a roof flashing is to be used, install the roof flashing appropriate to the roof pitch and install a round termination cap following the instructions shipped with the cap.

For chase installations you can use a round termination cap (TR11), a round telescoping termination cap (TR11T) or a square termination cap (ST1175). A chase installation must use a chase top. Chase tops are available from your Heatilator distributor. See page 20 for building a chase.

13.Installing the Outside Air Kit

The outside air kit is supplied as a standard feature with this fireplace and its use is highly recommended to minimize the effects of negative pressure within the structure. It is recommended to utilize the shortest duct run to optimize the performance of the outside air kit. The outside air kit inlet thimble should be positioned at least four feet above the ground level, in a manner that will not allow snow, leaves, etc. to block the inlet.

The outside air kit is installed on the left hand side of the fireplace. Remove the cover plate from the side of the fireplace assembly where the air kit is to be installed. See Figure 15 for handle location.

14.Installing the Chimney Air Kit

When installing the chimney air kit, follow the instructions provided with this accessory.

Figure 14 - Ceiling/Attic Construction

Figure 15 - Air Kit Handle Location

34922 Rev B

16

12-01

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 12-01 Rev B Table of Contents Safety PrecautionsDesign and Installation Considerations Listings and Code Approvals Description of the Fireplace SystemHeatilator fireplace system consists of the following Optional Components IncludeSystem Components Fireplace ComponentsChimney Components AK14 Outside Air KitChimney Sections Firestop SpacerChase Top Chimney Air Kit PRE-INSTALLATION Preparation Installation Along a Wall or an Exterior ChaseCorner Installation Fireplace Locations and Space RequirementsFraming the Fireplace Sidewalls/SurroundsOffset/Returns Offset Chart Using Offsets and ReturnsChimney Requirements Chimney Height Requirements above roof line Number of Sections RequiredInstallation of Fireplace Positioning the FireplacePlacing the Protective Metal Hearth Strips Leveling the FireplaceInstalling Firestop Spacers Assembling Chimney SectionsAttic Insulation Shield Double-checking the Chimney AssemblySecuring the Chimney System Installing the Roof Flashing Installing the Outside Air KitInstalling the Chimney Air Kit Marking the Exit Point of the RoofCompletion of the Enclosure Gas Log/Lighter ProvisionsHearth Extension Factory Built Hearth ExtensionPosition the Hearth Extension Finishing MaterialMantel Glass DoorsConstructing a Chase MaterialsChase Top Termination CapGeneral Information Outside Air Operating InstructionsFlue Damper Glass Doors Wood Fuel GrateFirescreen Proper Operating Positions of Bi-Fold DoorsDraft Problems Starting a FireFlue Draft Maintenance Instructions Chimney CleaningDisposal of Ashes Creosote and SootIndex Limited Warranty As part of its Limited WarrantyReplacement Parts Advantage How to Obtain Service

T4800 specifications

The Heatiator T4800 is an advanced heating solution designed to deliver exceptional performance and efficiency for residential and commercial spaces. This state-of-the-art heater combines innovative technologies with user-friendly features to ensure a comfortable atmosphere, regardless of the external weather conditions.

One of the standout features of the Heatiator T4800 is its powerful heating capacity. It can rapidly warm up large areas, making it ideal for open-plan living spaces and office environments. The unit employs a highly efficient heating element that ensures an even distribution of warmth, eliminating cold spots and enhancing overall comfort.

In terms of technology, the Heatiator T4800 integrates smart thermostatic controls. Users can easily set their desired temperature through a digital interface, allowing for precise adjustments. Additionally, the heater offers a programmable timer that lets users schedule heating cycles based on their routines, ensuring energy is not wasted when spaces are unoccupied.

Safety is paramount in the design of the T4800. It comes equipped with advanced features such as overheat protection and tip-over switches, which automatically cut off power to the unit if it becomes too hot or is inadvertently knocked over. This provides peace of mind, especially in households with children or pets.

Energy efficiency is another hallmark of the Heatiator T4800. The heater boasts a high Energy Efficiency Ratio (EER), which translates to significant savings on energy bills. Its environmentally friendly heating technology minimizes carbon emissions, making it a sustainable choice for environmentally conscious consumers.

The sleek and modern design of the Heatiator T4800 allows it to blend seamlessly with any décor. With a compact form factor, it can be placed nearly anywhere without taking up valuable space. Its whisper-quiet operation means it won’t disrupt daily activities or sleep, making it suitable for bedrooms, living rooms, and offices alike.

Moreover, the Heatiator T4800 is designed for easy maintenance. The accessible filter can be cleaned or replaced with minimal effort, ensuring optimal performance and longevity.

Overall, the Heatiator T4800 stands out in the crowded market of heating devices. Its combination of advanced features, efficiency, safety, and modern design makes it an outstanding choice for anyone looking to improve their indoor comfort.
Top Page Image Contents