Behringer B512DSP user manual Control elements and connections, Speech, Music

Page 6

EUROLIVE B512DSP

2. Control elements and connections

Fig. 2.1: Control elements and connections

Power is supplied via an IEC connector. The matching cable is provided with the unit.

Use the POWER switch to turn on the B512DSP. Before connecting the unit to the power mains, ensure that the POWER switch is in OFF position.

+Attention: The POWER switch does not fully disconnect the unit from the mains. To disconnect the unit from the mains, pull out the main cable plug or appliance coupler. When installing the product, ensure the plug or appliance coupler is readily operable. Unplug the power cord completely when the unit is not used for long periods of time.

Use the LEVEL control to adjust the signal gain of the MIC/LINE inputs. Before you connect or disconnect a signal source to or from one of the inputs, please turn the corresponding control fully to the left. Once the signal source is connected, increase the volume as desired by turning the control clockwise. Always make sure that the CLIP LED does not light up at all or with signal peaks only.

Line-level signals:

Devices with high output levels (e.g. the outputs of mixing consoles or CD players) only need little gain. In this case, the LEVEL control will mostly be positioned somewhere in the area marked “LINE” (left half of the control range).

Microphone signals

Low-level microphone signals need more gain. When microphones are used, the control will be positioned in the MIC area (right half of the control range).

+We would like to draw your attention to the fact that extremely loud sound levels may damage your hearing as well as your headphones/loudspeakers. Turn the LEVEL control fully to the left before you switch on the unit. Be careful to select a suitable volume at all times.

The CLIP LED lights up when the input signal level is too

high. In this case, turn the LEVEL control to the left until the LED goes out or only lights up at peak levels.

Use the MIC/LINE inputs (XLR connectors) for connecting audio signals.

The LINE OUT XLR jack provides the signal with no additional gain applied in order to connect another loudspeaker, for example. The output signal is a mix of both input signals. (See Chapter 4.2 for more information on how to use several loudspeakers)

The B512DSP is equipped with a 2-band tone control. Each band allows you to apply a maximum boost/cut of 15 dB, in its center position the equalizer is set to neutral.

Use the EQ HIGH control to cut or boost the treble range by 15 dB. The cut-off frequency is 12 kHz.

Use the EQ LOW control to cut or boost the bass range by 15 dB. The cut-off frequency is 100 Hz.

The B512DSP features a high-pass filter with a slope of

24dB/oct. to eliminate unwanted low-frequency content, such as pop sounds produced by hand-held microphones, or rumble or wind noise when using high-sensitivity microphones. The LOW CUT control adjusts the cut-off frequency. If you want to use the B512DSP in combination with a subwoofer, you can use the high-pass filter to lower the bass range reproduced by the subwoofer. This allows you to operate the B512DSP even without an external frequency crossover. Set the cut-off frequency to the highest frequency that can be reproduced by the subwoofer.

The CONTOUR switch governs the dynamic contour filter:

SPEECH

Setting the CONTOUR switch to SPEECH (switch not pressed) will optimize the frequency response for speech applications. This ensures better intelligibility.

MUSIC

Setting the CONTOUR switch to MUSIC (switch pressed) will optimize the frequency response for music playback.

The TIMED TURNOFF switch activates the automatic turn- off function:

ON

When the switch is actuated (ON position), the automatic turn-off function is active. The loudspeaker is turned off automatically when it receives no signal for more than 3 minutes. As soon as a signal is received, the loudspeaker is switched back on.

6

2. Control elements and connections

Image 6
Contents B512DSP Eurolive Important safety instructions Eurolive B512DSPEurolive Table of contents ForewordIntroduction Before you get startedIntroduction Speech Control elements and connectionsControl elements and connections MusicSetting up the B512DSP Setting up the B512DSPHow to avoid feedback TweeterApplication examples PresentationsPA systems Installation InstallationOther uses Specifications Warranty WarrantyEurolive B512DSP