X2 manual Adat Sync, Headphones, To synchronize the X2 to an Adat system

Page 30

Connecting the X2

Headphones

The PHONES connector (found on the front end of the console, directly below the Master faders) is a stereo 1/4" jack which provides a substantial level to drive most headphones. The signal level is controlled by the PHONES knob. The wiring scheme is as follows.

Headphones

Left Signal

Right Signal

Ground

Tip

Ring

Tip

Ring

Sleeve

Sleeve

ADAT Sync

The ADAT SYNC is a 9-pin, D connector which is designed to connect to an ADAT system. The X2 uses the proprietary timecode found on an ADAT formatted tape to synchronize its Dynamic Mute Automation system to tape. For more information, refer to Chapter 5.

To synchronize the X2 to an ADAT system:

1Connect one end of a male/male, D connector cable to the SYNC OUT connector of the last ADAT in your system.

2Connect the other end of this cable to the ADAT SYNC connector on the back of the X2.

MIDI

The MIDI IN, OUT and THRU are standard 5 pin DIN connectors, and are provided for interfacing the Dynamic Mute Automation system with a MIDI sequencer or other MIDI devices. The MIDI IN connector is for connecting to the MIDI Out of a MIDI device, while the MIDI OUT connector is for connecting to the MIDI In of the device. The X2’s MIDI THRU connector is provided for connecting other MIDI equipment that you wish to control from the MIDI device you have connected to the X2’s MIDI IN and MIDI OUT connectors.

For more information see Chapter 5.

X2 Reference Manual

29

Image 30

Contents Alesis Conventions How To Use This ManualIntroduction Description of Controls. a dictionary of each controlX2 Reference Manual Contents Applications Description of Controls Trouble-Shooting Midi Implementation Chart Page Introduction AboutBasic Principles of Mixing & Multitrack Recording Recording/TrackingMonitoring Mixdown Introduction X2 Reference Manual Guided Tour Recorder/Mix SystemsPage Aux Send/Return Systems Control Room Systems Muting AutomationMeter Bridge Page Page Connections PowerPower Supply Unpacking and InspectionTo connect the power supply to Avoiding Ground Loops To Eliminate HUM if the Above has FailedChannel Inputs and Outputs Balanced Mic InputsUnbalanced Line Inputs Page Tape Send Direct Output +4/-10 SwitchTape Input InsertBalanced Tape I/O To connect an Elco cable toGroup Inserts Stereo Returns and GroupsGroup Outputs Aux a & B ReturnsMaster Inserts Master Inputs and OutputsMaster Outputs Control Room OutputsPage Headphones Adat SyncTo synchronize the X2 to an Adat system Input Connector Type Examples of ConnectionsInterfacing to an Unbalanced -10 dBV Multitrack Recorder To interface with a typical unbalanced multitrack recorderInterfacing to a Professional +4 dBu Multitrack Recorder Interfacing to the Mixdown Deck Interfacing to Adat Using Elco ConnectorsInterfacing to a Multitrack Recorder via a Patchbay To connect the mixdown deck toInterfacing to the Headphone Amp Interfacing to the Control RoomInterfacing to the Studio Interfacing Aux Sends and Returns to Outboard EffectsConnecting Simultaneously, if desired Interfacing the Inserts Interfacing with a Midi SequencerTo interface a Midi sequencer with Recording Setting LevelsApplications II. Maintain Proper Fader LevelsRecording a Single Source to One Track To record a single source to a single trackRecording Multiple Sources to One Track To record two or more sources to a single trackRecording Multiple Sources to Two Tracks Stereo To record multiple sources to two tracks stereoTo select the meter bridge mode Recording TipsAbout Metering Overdubbing To listen to tape tracks on the Monitor fadersTo listen to tape tracks on the Channel faders Applications Previous section X2 Reference Manual Getting the Mix to the Headphones Monitoring Midi Virtual TracksTo route the mix to a headphone amp Adding Effects Selecting an Aux SendTo set the level going to the effects device To hear effects in the monitors To hear effects in the headphone/cue mixTo record effects onto the multitrack To bounce one or more tracks to another track mono Bouncing TracksTo record effects onto the mixdown deck To bounce multiple tracks to two tracks stereoGetting the Mix to the Tape Deck Playback/Mix-DownMixdown Basics Here is a simplified step-by-step way to establish a mixCreating a Dependable Mix To create a dependable mixMute Automation Page Live Performance Using Group Faders as SubgroupsTo configure the X2 mixer in order to achieve a mono mix Creating a Monitor MixVideo Post-Production Stage Monitor MixTo create two different stage monitor mixes Applications X2 Reference Manual Mute Automation OverviewTo enable destructive solo mode Destructive SoloMute Groups Page Defining Mute Groups To define Mute GroupsTo recall a Mute Group Recalling Mute GroupsOverlay Button To return the console to its previous mute statusSelecting a Sync Source Display ModeSynchronization Getting On-line/LockingUndoing Mute Events Mute EventsRecording and Playing Back Mute Events OverdubbingPage Editing Songs ErasingTo erase all events on all channels Erase All MemoryTo erase all events on one or more channels To erase a Song including its mute events and 4 Mute GroupsCopy Song CopyingCopy Mute Events To copy mute events from one channel to anotherMidi Channel Selecting Songs via MidiTo set the Midi channel Midi Map Receiving System Exclusive Memory BackupTransmitting System Exclusive Remaining MemoryDescription of Controls Input Channel ControlsHi and Lo EQ HPF SwitchTo MON Switch Hi Mid and Lo Mid EQAUX Source Switch EQ in SwitchSwitch Aux 3/4 AUX 1-2, AUX 1-2 PANMonitor Peak LED Switch Aux 5/6Monitor PAN Monitor Solo ButtonChannel PAN DIR SwitchGroup Assign Switches 1-2, 3-4, 5-6 Channel Peak LEDAux Master Controls Stereo Aux Return ControlsStereo Separation AUX a Assign Switches Aux a OnlyGroup Masters Switch Aux B Only BalanceSolo Button Group Master ControlsButton Mute ButtonGroup 1-8 Master Faders Solo LED and Level Master ControlsOscillator Frequency and Level Studio Level and AssignmentMaster Faders PhonesControl Room Level and Source Meter BridgePage Mute Automation Controls DisplayMute Groups Online Erase FWD and Erase BWD Buttons Memory RemainingErasing Memory Mute SoloDescription of Controls X2 Reference Manual Checking the Software Version TROUBLE-SHOOTINGTrouble-Shooting Index Re-initializingWarranty Information Maintenance/ServiceCleaning and Maintenance Obtaining Repair ServiceCustomers outside the USA Trouble-Shooting X2 Reference Manual Midi Maps Index MapsMute Midi Note Number Map Mute Midi Controller NumberMap Number Interval Midi Implementation Chart Specifications Input Module Power SupplyMaximum Gain Group ModuleTotal Shipping Weight DimensionsWeight Dimensional DrawingsInternal Connector Pinouts Block Diagram Index SoloSong LED 102