Behringer PMP1280S, PMP980S Digital Effects Processor, Installation, Rear panel, Mains connection

Page 7

EUROPOWER PMP960M/PMP980S/PMP1280S User Manual

nect the CD/TAPE IN from the recorder, before you start recording!

[38]The MAIN ¼" connectors allow you to send the main signal to an external amplifier, when you only wish to use the mixer and effects section. The signal is taken pre-power stage of the mixer. It is also possible to use only the left jack of the output. The PMP960M has only one mono output connector.

[39]Connect your monitor power amps or active monitor speak- ers to the mono MONITOR output to monitor the signal mix created with the MON controls or to route it to the musicians on stage.

[40]Use the POWER switch to put the unit into operation. The POWER switch should always be in the “Off” position when you are about to connect the unit to the mains.

◊Please note: The POWER switch does not fully disconnect the unit from the mains. Unplug the power cord completely when the unit is not used for prolonged periods of time.

2.4 Rear panel

[41]The mains connection is on a standard IEC receptacle. An appropriate power cord is supplied with the unit.

[42]FUSE HOLDER. Before connecting the unit to the mains, ensure that the voltage setting matches your local voltage. Blown fuses should only be replaced by fuses of the same type and rating. Please also read the information given in chapter 6 “Specifications”.

[43]Loudspeaker OUTPUT A.

PMP980S/PMP1280S: Depending on the operating mode selected (see (28)) either the left main signal or the monitor signal is provided at OUTPUT A. Never use this output in bridged mono mode.

PMP960M: In MON/MAIN mode, the monitor signal is provided at OUTPUT A (see (28)). Never use this output in bridged mono mode, except when you use a cable with the normal pin connections (pins 1+/1-). In this case you can take the mono main signal from this output in MAIN/

MAIN (BRIDGE) mode (not bridged). Please also refer to chapter 4.3 “Loudspeaker connection”.

◊The impedance of the loudspeaker connected must not fall below 4 Ω.

◊Please note that the power delivered to the speaker in bridged mono mode is considerably higher than in other

operating modes. Please read the information given on the rear panel of the power mixer.

[44]Loudspeaker OUTPUT B.

PMP980S/PMP1280S: Depending on the operating mode selected (see (28)) either the right main signal, the mono main signal or the bridged mono signal is provided at

7

OUTPUT B.

PMP960M: Either the main or the bridged main mono signal is provided at OUTPUT B (see (28)). When you use a cable with the normal pin connections (pins 1+/1-), it is possible in MAIN/MAIN (BRIDGE) mode to take the mono main signal from this output (not bridged). Please also refer to chapter 4.3 “Loudspeaker connection”.

◊In BRIDGE mode, always connect only one loudspeaker with an impedance of at least 8 Ω to OUTPUT B (pins 1+/2+)! Please note that OUTPUT A must NEVER be used in

BRIDGE mode (with pin connections 1+/2+)!

◊In all other operating modes, the minimum impedance of the speaker connected must not fall below 4 Ω.

◊Information on how to properly connect your speaker with regard to polarity can be found on the rear of the mixer

(PINOUTs).

[45]SERIAL NUMBER.

3. Digital Effects Processor

24-BIT MULTI-EFFECTS PROCESSOR

This built-in effects module produces high-grade standard effects such as reverb, chorus, flanger, delay and various combi- nation effects. The integrated effects module has the advantage of requiring no wiring. This way, the danger of creating ground loops or uneven signal levels is eliminated at the outset, com- pletely simplifying the handling.

These effect presets are designed to be added to dry signals. If you move the FX RET control, you mix the channel signal (dry) and the effect signal.

◊Turn down the FX controls in those channel strips whose signals you don’t wish to process.

4. Installation

4.1 Mains connection

Blown fuses must be replaced by fuses of the same type and rating.

The mains connection is made using the enclosed power cord and a standard IEC receptacle. It meets all of the international safety certification requirements.

◊Please make sure that all units have a proper ground con- nection. For your own safety, never remove or disable the ground conductor from the unit or of the AC power cord.

4.2 Audio connections

The inputs and outputs of the BEHRINGER EUROPOWER are unbalanced ¼" TS connectors—except for the balanced mono line inputs. Of course, all inputs and outputs work with both bal-

ENGLISH

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Thank you Table of ContentsImportant Safety Instructions Online registration Before you get startedShipment Initial operationFront Panel Rear Panel Main and monitor section Control ElementsMono and stereo channels Effects sectionConnectors Mains connection InstallationDigital Effects Processor Rear panel¼ TS connector +2 front view +2 rear view Loudspeaker connectionEuropower mixer as a stereo amplifier example Wiring ExamplesStandard set-up example Microphone Inputs SpecificationsDisplay DIMENSIONS/WEIGHT § 1 Warranty Warranty§ 6 Claim for damage Legal Disclaimer

PMP980S, PMP1280S specifications

Behringer, a renowned name in audio equipment, offers an impressive lineup of powered mixers, notably the PMP1280S and PMP980S. These versatile mixing consoles are designed to cater to musicians, bands, and live sound engineers who require robust performance and user-friendly features in a compact format.

The Behringer PMP1280S is a powerful 12-channel powered mixer featuring an impressive total power output of 2 x 800 watts. This translates to ample headroom and clarity for live performances, ensuring that sound remains pristine, even at higher volumes. The mixer includes 8 mono channels with 3-band EQs, providing artists with control over their sound while maintaining simplicity. Each channel also features a built-in compressor to smooth out dynamic peaks and ensure a more consistent output. The PMP1280S is equipped with various onboard effects, including reverb, delay, and modulation, making it easier for users to enhance their sound without needing additional equipment.

On the other hand, the PMP980S, a slightly smaller powered mixer, boasts 8 channels and a power output of 2 x 500 watts. It retains many of the features found in the PMP1280S, including the 3-band EQ per channel, but is designed for those who need a more lightweight solution without sacrificing sound quality. This model also comes with built-in effects and a simple layout that makes it accessible for live performances, rehearsals, or presentations.

Both mixers utilize Behringer's proprietary Ultra-low Noise preamps, which are designed to produce high-quality audio while reducing unwanted noise. Moreover, the mixers feature a 24-bit digital effects processor, allowing users to create stunning sonic landscapes in real-time. Connectivity is another strong point, with multiple inputs and outputs, including XLR and TRS options for versatile integration with microphones and instruments.

The redundancy in power supply and thermal protection systems ensures that users can rely on these mixers during critical performances. Whether you're in a small venue or a larger space, both the PMP1280S and PMP980S provide exceptional performance, reliability, and a host of features that make them suitable for various audio applications.

In conclusion, Behringer's PMP1280S and PMP980S exemplify the brand's commitment to delivering professional-grade audio solutions that meet the diverse demands of modern audio professionals. With their powerful outputs, versatile effects, and high-quality components, these mixers are excellent choices for anyone looking to elevate their sound experience.
Top Page Image Contents