EURORACK UBB1002
1.3Control elements
1.3.1Interface panel
Use this balanced XLR jack to connect a microphone to the UBB1002 (applies to channels 1 through 7/8).
+The phantom power required for condenser mics
can be activated with switch 
. Please note that in
Channels 1 and 2 feature an additional LINE input on a balanced 1/4" jack.
The INSERT jack allows you to insert, for example, a compressor or equalizer in the mono channels.
These are the two balanced LINE inputs on 1/4" jacks for the left and right sides of the stereo channels, which can be used in parallel to the microphone inputs.
Use the TAPE OUT jacks to connect, for example, a tape deck for recording applications.
The TAPE IN jacks (on stereo RCA and 1/4" jacks) allow for the connection of
Use the PHONES jack to connect a commercially available pair of headphones.
These are the balanced 1/4" jack MAIN OUTPUTS of your UBB1002 that can be used to drive, e.g. a power amplifier.
The MON SEND connector provides the monitor signal of your UBB1002, for example, to control a monitor amplifier or active monitor speaker.
Connect the FX SEND connector to the input of an external effects device.
+The UBB1002 has no dedicated FX Return connectors. However, you can connect the outputs of an external effects device to the 1/4" jack inputs of the stereo channels or channels 9/10. In this case, the stereo channel’s FX control must be set to
1.3.2 Front panel
The mono channels 1 and 2 of your UBB1002 feature the same control elements. Therefore, the following description of channel 1 also applies to channel 2.
The GAIN MIC control determines the channel’s input gain, both for a microphone connected via the XLR jack and for other signal sources connected to the 1/4" jack. Adjust the signal gain so that the Clip LED below the control lights up during peak signal only, but never permanently. In battery- operated mode the Clip LED is switched off.
Use the PAN control to adjust the signal’s position on the stereo basis.
Your UBB1002 comes with a
The CHANNEL fader adjusts the volume of the corresponding channel.
Use the MON control to determine the channel volume sent to the monitor mix bus. When set fully to the left, the channel volume in the monitor mix is zero.
The FX control adjusts the effects volume for the corresponding channel.
The stereo channels 3/4, 5/6, and 7/8 differ from channels
1 and 2 – not only with regard to the connectors provided. They also have two GAIN controls, i.e. you can connect a microphone and a stereo line signal at the same time!
+When you connect a microphone to a stereo channel on the UBB1002, the input gain is governed by the GAIN MIC control!
The GAIN LINE control is used to adjust the line input gain. Here, too, the signal can be monitored visually with the Clip LED.
The BAL control performs two functions: When you connect a microphone via the XLR connector, or another signal source via the L/MONO jack, the BAL control determines the signal position on the stereo basis. When both 1/4" jack inputs (L & R) are used, the BAL control adjusts the volume balance of the two sources connected.
Except for the GAIN MIC control and a different set of connectors, the channels 9/10 feature the same control elements
as the stereo channels. See 
& 
and 
through 
.
1.3.3 Main section
The LEVEL DISPLAY reads the output level of your UBB1002. Make sure that the two Clip LED’s won’t light up.
Use this switch to activate the phantom power required for condenser microphones. In
The MON SEND control adjusts the volume level of the
monitor signal provided at connector 
.
Use the MASTER fader to set the overall volume level of your UBB1002.
The FX SEND control allows you to adjust the level that is
sent to an external effects device via connector 
. Thus, you can drive all types of effects devices without any risk of distortion.
The PHONES control governs the headphones volume.
Connect the enclosed power supply to the AC POWER IN jack.
Use the POWER ON switch to switch on your UBB1002, which is indicated by the LED below the LEVEL DISPLAY 
.
SERIAL NUMBER. Please take the time to have the warranty card filled out completely, and return it within 14 days after the date of purchase, so as to be entitled to benefit from our extended warranty. Or use our online registration option available on the World Wide Web at www.behringer.com).
1. INTRODUCTION | 5 |