Campbell Hausfeld NB0050 operating instructions Fasteners

Page 5

Operating Instructions

Model NB0050

 

 

4.The driver cover plate can now be rotat- ed, exposing the jammed fastener.

5.Remove the jammed fas- tener, using pliers or a screwdriver if required.

6Rotate driver cover back into the closed posi- tion.

7.Extend the wire latch and place over the hooks on the nose casting.

8.Close the over center latch by pushing the latch in until the latch snaps into place.

Technical Support

Should you have any questions regard- ing the operation or repair of this nail- er, please call our Nailer Hotline at

1-800-543-6400 for assistance. If you are calling from Ohio or outside of the continental United States, please call collect, 1-513-367-1182.

Record the model number and serial number below:

Model No___________________________

Serial Number_______________________

Retain these number for future reference.

Fastener And Replacement Parts

Use only

genuine Campbell Hausfeld fasteners (or equivalent) and replacement parts. Do not use modi- fied parts or parts which will not give equivalent performance to the original equipment. Tool performance, safety and durability could be reduced. When ordering replacement parts or fasten- ers, specify by part number.

COLORMATCH™ System

The Campbell Hausfeld Finishing Nailer has a unique COLORMATCH™ stripe. Look for the COLORMATCH™ stripe to choose the right Campbell Hausfeld fasteners for your NB0050 2” finish nailer.

Nailer Repair

Nailer repairs must be performed by qualified and experienced service peo- ple ONLY.

Assembly Procedure For Seals

When repairing a nailer, the internal parts must be cleaned and lubricated. Parker O-lube or equivalent must be used on all o-rings. Each o-ring must be coated with O-lube before assembling. A small amount of oil must be used on all moving surfaces and pivots. After reassembling, a few drops of 30W non- detergent oil or equivalent, must be added through the air line before test- ing.

Fasteners

The following Campbell Hausfeld finishing nails are available at local retail stores. If you need help locating any item, call customer service at 1-800-543-6400. Campbell Hausfeld nails meet or exceed Federal Specifications FF-N-105B.

Model #

Length

Shank

Finish

Head

Collation

Nails Per

Nails Per

Gauge

Stick

Box

 

 

 

 

 

 

 

 

 

 

 

 

 

FB003060

1-1/4”

16 Gauge

Galvanized

Brad

Adhesive

50

2500

FB004060

1-1/2”

16 Gauge

Galvanized

Brad

Adhesive

50

2500

FB004560

1-3/4”

16 Gauge

Galvanized

Brad

Adhesive

50

2500

FB005060

2”

16 Gauge

Galvanized

Brad

Adhesive

50

2500

Interchange Information

Nails used in the Campbell Hausfeld NB0050 Finishing Nailer will also work in Hitachi NT65A, Paslode 3250-F16, IM250F, Duo Fast LFN-764, Sears 18314, Porter Cable FN200 and FN250.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Model NB0050 General Safety InformationDescription Model NB0050 Nailer Components And SpecificationsRecommended Hookup Using The NailerOperational Modes Operating The Nailer Fasteners Problem Cause Solution Troubleshooting GuideWhat is not Covered Under this Warranty Limited WarrantyNB0050

NB0050 specifications

Campbell Hausfeld NB0050 is a versatile and efficient air compressor that caters to both novice DIY enthusiasts and seasoned professionals alike. Known for its reliability and compact design, the NB0050 is an ideal addition to any workshop or garage. This air compressor stands out due to its powerful performance and user-friendly features.

One of the main features of the Campbell Hausfeld NB0050 is its 5.0-gallon air tank, which allows for extended operation between refills. This sizeable air tank not only provides consistent airflow but also helps to reduce the frequency of compressor cycling, extending the lifespan of the unit. The compressor is equipped with a powerful 1.0 horsepower motor that delivers up to 125 PSI, ensuring it can handle a wide range of tasks, from inflating tires to powering pneumatic tools like nail guns and impact wrenches.

The NB0050 utilizes an oil-lubricated, cast iron pump, which contributes to its durability and longevity. This type of pump provides superior cooling and reduces friction, making it ideal for heavy use. The compressor is also designed with a low noise level, operating at around 68 dBA, making it a more pleasant option for various environments, especially where noise control is a consideration.

Portability is another key characteristic of the Campbell Hausfeld NB0050. It features a sturdy handle and rubberized wheels that make it easy to transport between job sites or to move around the garage. Despite its robust construction, the design ensures it remains lightweight enough to be handled comfortably.

Moreover, the NB0050 comes with essential safety features, including a thermal overload protection system that prevents overheating during prolonged operation. This added layer of safety ensures that users can operate the compressor without worry, making it suitable for both home and professional environments.

In addition to its impressive capabilities, the Campbell Hausfeld NB0050 is backed by a manufacturer’s warranty, providing peace of mind to buyers. Overall, its combination of power, efficiency, and portability makes the Campbell Hausfeld NB0050 a top choice for anyone in need of a reliable air compressor for a variety of applications. Whether tackling home improvement projects or professional tasks, this model is designed to exceed expectations and deliver exceptional performance.
Top Page Image Contents