Peavey 500 operation manual Probass

Page 24

PROBASS 500™

SPECIFICATIONS

SYSTEM SPECIFICATIONS

Mains Circuit Breaker:

5amps

Mains Voltage:

120 VAC 60 Hz

Power Consumption:

600 Watts

Hum and Noise:

Typically greater than -80 dB unweighted. With controls set as follows:

Pad = passive

Bright = Normal (out)

Low Cut = Normal (out)

Pre Gain = 9 o’clock (roughly 2) Post Gain = 10

Contour = 0 Low = 0 High = 0

Parametric Band 1: cut/boost = 0; bandwidth = 0; frequency = 0 Parametric Band 2: cut/boost = 0; bandwidth = 0; frequency = 0 Parametric Band 3: cut/boost = 0; bandwidth = 0; frequency = 0 Master Volume = 5

POWER AMPLIFIER SECTION

Protection:

Electronic current limit protection circuit Thermal protection circuit

D.C. crowbar protection circuit DDT speaker protection circuit with defeat switch and LED

Variable speed fan‚ thermally controlled

General Information:

Minimum Load = 2 Ohms Input sensitivity: 1.0 VRMS

Two 1/4" speaker jacks and one Neutrik Speakon® all in parallel

Rated Power Output:

500 Watts (31.62 VRMS) into 2 Ohms

350 Watts (37.42 VRMS) into 4 Ohms

200 Watts (40.00 VRMS) into 8 Ohms

Noise:

Typically greater than 102 dB below full power @ 8 Ohms unweighted

DDT Dynamic Range:

Typically greater than +15 dB

Frequency Response:

+0/-0.61 dB‚ 100mW to 160 w RMS 20 Hz to 20 kHz (8 Ohm load‚ typically below 0.2% THD+N)

PREAMP SECTION

Settings for measurements unless otherwise noted:

Pad = passive (out) Bright = Normal (out) Low Cut = Normal (out) Pre Gain = 2

Post Gain = 10 Contour = 0 Low = 0 High = 0

Parametric Band 1: cut/boost = 0; bandwidth = 0; frequency = 12 o’clock Parametric Band 2: cut/boost = 0; bandwidth = 0; frequency = 12 o’clock Parametric Band 3: cut/boost = 0; bandwidth = 0; frequency = 12 o’clock Master Volume = 5

Line Out Level = 10 (fully clockwise)

Input Sensitivity (level to achieve full power):

With Pad out:

Nominal input: 100 mV RMS

Minimum input: 5 mV (pre gain @ 10)

Maximum input: 2.0 V (pre gain @ 1) With Pad -10 dB in:

Nominal input: 316 mV RMS

Minimum input: 16 mV (pre gain and master fully CW)

Maximum input: 6.3 V (pre gain @ 1)

Equalization:

Bright Boost: +8 dB @ 5.5 kHz

Low Cut: -3 dB @ 125 Hz

Contour: Set @ 10 provides +4 dB @

35 Hz; -30 dB @ 400 Hz; +4 dB @ 5.5 kHz

Low: +/-15 dB @ 20 Hz; Shelving type EQ

High: +/-15 dB @ 5 kHz–20 kHz; Shelving type EQ

Parametric Band 1: cut/boost = +12 dB/ -20 dB; BW (Q) = 0.3–8.5, Frequency = 40 Hz–400 Hz

Parametric Band 2: cut/boost = +12 dB/ -20 dB; BW (Q) = 0.3–8.5, Frequency = 150 Hz

Parametric Band 3: cut/boost = +12 dB/ -20 dB; BW (Q) = 0.3–8.5, Frequency = 800 Hz–8 kHz

Tuner Send:

Instrument level through a buffer

Line Out:

-∞ to fx loop level for post setting (for nominal input)

-∞ to instrument level for pre setting (for nominal input)

Effects Loop:

Set for -10 dB (0.315 VRMS) with post gain @ 5; Master @ 10

Controlled via footswitch‚ ground tip to defeat

Preamp Output:

1 VRMS nominal

Dimensions:

Width: 19.000" (48.26 cm)

Depth: 12.750" (32.39 cm)

Height: 3.500" (8.89 cm)

Weight: 24.8 lb (11.25 kg)

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Page Page Important Safety Instructions Probass Mute switch Input pad switchHi boost switch Low cut switchMaster volume DDT enable/disable switchPower LED/DDT indicator Power switchGround polarity switch Reset/circuit breaker switchIEC connector/detachable line cord Power amp inputLine out ground lift switch Select switchEffects send Effects mixProbass Suggested Settings Old.timer ProBass 500 Block Diagram Español Interruptor de mute LED de estatus del muteEntrada Interruptor de pad de entradaVolumen Maestro LED de estatus de señal verdeIndicador de saturación de señal rojo EQ paramétrico de 3 bandasInterruptor de cambio de polaridad de tierra Interruptor automático breakerConectador IEC/Cable de corriente Salidas para parlantesRetorno de efectos 35 envío de efectosMezcla de efectos Interruptor de tierra de línea de salidaProbass Français Interrupetur de mode silencieux mute Led de mode silencieux muteJack d’entrée Atténuateur d’entréeLed de signal Verte Led de niveau de seuil maximum clip RougeEQ paramétrique 3-bandes 15‚ 18‚ 21 bandes de fréquences bandwidth QInterrupteur de polarité Interrupteur de réinitialisation du coupe circuitCordon d’alimentation IEC Sorties hauts-parleursLine out signal basse impédance symétrisé 37 Sélecteur de référence de masse de la sortie ligne38 Sélecteur de type de signaux de la sortie ligne Entrée auxiliaireProbass Deutsch Mute-Schalter Mute-Status-LEDInput-Klinke Input-Pad-SchalterSignalstatus-LED grün Signal-Clip-Anzeige rotContour-Regler Parametrischer 3-Band-EQPower LED/DDT-Anzeige Power-SchalterReset/Circuit-Breaker-Schalter Ground-Polarity-SchalterFernbedienungsschalter Ground-Lift-Schalter für Line-AusgangLine Out symmetriert Line-Out-PegelreglerProbass Peavey Electronics Corporation Limited Warranty 80304909
Related manuals
Manual 48 pages 11.58 Kb

500 specifications

The Peavey 500 is a powerful and versatile amplifier that has garnered praise from musicians and audio engineers alike. Known for its robust performance and reliability, the Peavey 500 is designed for a variety of applications, including live performances, studio recordings, and worship settings. With a blend of innovative technologies and practical features, this amplifier stands out in the crowded market of pro audio equipment.

One of the key features of the Peavey 500 is its impressive power output. Offering substantial wattage, this amplifier is capable of driving even the most demanding speaker systems with ease. Competitively designed to handle both high and low frequencies, it ensures clarity and fullness of sound, making it an excellent choice for bassists and guitarists who require punchy, dynamic tones.

The Peavey 500 incorporates several exclusive technologies to enhance its performance. One such innovation is Peavey’s proprietary TransTube technology, which emulates the warm, harmonic-rich tones of vacuum tube amplifiers. This allows musicians to achieve a rich and vibrant sound without carrying the weight and maintenance demands of traditional tube amps.

In addition to its sound quality, the Peavey 500 is equipped with built-in EQ controls, allowing users to tailor their sound to suit different performance environments. Its comprehensive tone-shaping capabilities include bass boost, midrange adjustments, and treble controls, enabling precise sound customization. This flexibility is crucial for musicians who often perform in varied acoustic spaces.

Durability is another hallmark of the Peavey brand, and the Peavey 500 is no exception. Engineered with high-quality components and a rugged construction, this amplifier is built to endure the rigors of frequent transportation and heavy use. From the solid chassis to the robust input and output connectors, every aspect of the Peavey 500 reflects a commitment to long-lasting performance.

Furthermore, the amplifier features multiple input options, including standard quarter-inch jacks and XLR connections, ensuring compatibility with a wide range of instruments and audio sources. The versatility of the Peavey 500 is further enhanced by options for direct outputs, making it easy to connect to recording systems or external mixers.

Overall, the Peavey 500 stands as a testament to Peavey’s dedication to quality and innovation in the music industry. With its powerful output, advanced technologies, and user-friendly features, it continues to be a go-to choice for musicians seeking reliability and exceptional sound in their performances. Whether on stage or in the studio, the Peavey 500 delivers the performance that professionals expect and deserve.
Top Page Image Contents