center position the kill function is not active, and the fre- quency will not be killed. When you move the selected KILL SWITCH to the bottom FLASH position and hold it there, the frequency will be killed. Releasing the selected KILL SWITCH from the bottom position will bring it back to the center position and the frequency will no longer be killed.
5.CROSSFADER SECTION: The CROSSFADER (21) allows the mixing of one source into another. The left side of the CROSSFADER (21) is CHANNEL 1 and the right side is CHANNEL 2. The CROSSFADER (21) in your unit is removable and if the need arises can be easily replaced. Your Gemini mixer comes with an
USER REPLACEABLE CROSS FADER
1.Unscrew the outside mixer FACE PLATE screws and remove the face plate. Then remove FADER plate screws (B & C).
2.Carefully lift the fader and unplug the CABLE (D).
3.Plug the new fader into the cable and place it back in the mixer.
4.Screw fader plate to the mixer and replace the mixer FACE PLATE.
Note: Do not apply pressure while using the Crossfader. Lightly glide the Crossfader back and forth. Pressing down on the controls can bend contacts and cause a loss of sound.
6.CURVE CONTROL: The CROSSFADER CURVE SWITCH (12) allows you to adjust the kind of curve the crossfader has. Depress the crossfader curve button to make the curve steep and cutting (perfect for scratching). Release the crossfader curve button to make the curve gradual and gentle.
7.HAMSTER CONTROL: The CROSSFADER REVERSE SWITCH (11) allows you to reverse the cross- fader so that CHANNEL 2 (31) is controlled by the left side of the crossfader and CHANNEL 1 (19) is controlled by the right side of the crossfader.
NOTE: When the CROSSFADER REVERSE SWITCH (11) is activated (moved to the right), only the crossfader reverses. The Channel Slides, Gain, Kill Switches and tonal controls do not reverse.
8.CUE: Cue facilitates the seamless blending of one recorded track into another. Connecting a set of head- phones to the HEADPHONES (8) jack allows you to moni- tor either Channel 1 or Channel 2. Select CHANNEL 1 (19) by moving CUE FADER (18), located on the front panel, to CUE 1 on the left. Listen to Channel 2 by mov- ing CUE FADER (18) to CUE 2 on the right. To mix both Channels bring CUE (18) to the middle so that both tracks may be heard. Use CUE VOLUME (9) to adjust the head- phone volume without affecting the
09.MIC SECTION: Connecting a microphone to the 1/4" MIC JACK (10) allows voice amplification through the mixer to the stereo through the MASTER RCA OUTPUTS
(3) . This is controlled by the MIC VOLUME (16), HIGH (15), LOW (14) rotary controls.
10.OUTPUT CONTROL SECTION: The level of the MASTER OUTPUT (3) is controlled by the MASTER VOLUME (13) rotary control.
11.VU METER: The VU METER (25) LEDs indicates the MASTER RCA OUTPUT (3) in stereo. VU METER (25) LEDs reflect the VOLUME (13), GAIN (24,32), HIGH (23,33), MID (22,34) and LOW (21,35) rotary control adjustments for each channel. The CHANNNEL SLIDES (19, 31) also affect each of the VU METER (25) LEDs.
SPECIFICATIONS:
INPUTS: |
|
DJ Mic | 1.5 mV 1 kOhm Balanced |
Phono | 3 mV 47 kOhm |
Line | 150 mV 10 kOhm |
OUTPUTS: |
|
Amp | 0 dB 1V 400 Ohm |
Max | 20V Peak to Peak |
GENERAL: |
|
Bass (Channels | |
Mid (Channels | |
High (Channels | |
Gain (Channels | 0 to |
Frequency Response | 20 |
Distortion | Less Than 0.02% |
S/N Ratio | Better Than 80 dB |
Headphone Impedance | 32 Ohm |
Power Source Adapter | 115V/15V AC 0.5A |
........................................................................................ | or 230V/15V AC 0.5A |
Unit Dimensions | W 10" x H 3.3" x D 10.25" |
.......................................................................................... | (254 x 84 x 260mm) |
Weight | 6.2 lbs ( 2.81 kg) |
NOTE: SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE WITHOUT NOTICE FOR PURPOSE OF IMPROVEMENT.
(5)