Behringer MDX2200 manual Specifications, Audio Input

Page 28

 

COMPOSER PRO MDX2200

 

 

8. SPECIFICATIONS

 

AUDIO INPUT

 

Connectors

XLR and 1/4" jack

Type

RF filtered, servo-balanced input

Impedance

50 kOhm balanced, 25 kOhm unbalanced

Nominal operating level

+4 dBu/-10 dBV switchable

Max. input level

+21 dBu balanced and unbalanced

CMRR

typ. 40 dB, >55 dB @ 1 kHz

AUDIO OUTPUT

 

Connectors

XLR and 1/4" jack

Type

Electronically servo-balanced output stage (optional transformer-

 

balanced).

Impedance

60 Ohms balanced, 30 Ohm unbalanced

Max. output level

+21 dBu, +20 dBm balanced and unbalanced

SC INPUT

 

Connector

1/4" jack

Type

RF-rejecting, DC de-coupled, unbalanced input

Impedance

>10 kOhm

Max. input level

+24 dBu

SC OUTPUT

 

Connector

1/4" jack

Type

RF-rejecting, DC de-coupled, unbalanced output

Impedance

2 kOhm

Max. output level

+21 dBu

SYSTEM SPECIFICATIONS

 

Bandwidth

20 Hz to 20 kHz, +0/-0.5 dB

Frequency response

0.35 Hz to 200 kHz, +0/-3 dB

Noise

>-95 dBu, unweighted, 22 Hz to 22 kHz

THD

0.008 % typ. @ +4 dBu, 1 kHz, Gain 1

 

0.04 % typ. @ +20 dBu, 1 kHz, Gain 1

IMD

0.01 % typ. SMPTE

Crosstalk

<-100 dB, 22 Hz to 22 kHz

Stereo coupling

True RMS detection

EXPANDER/GATE SECTION

 

Type

IRC (Interactive Ratio Control) expander

Threshold

variable (OFF to +15 dB)

Ratio

variable (1:1 to 1:8)

Attack

<1 ms / 50 dB, program dependent

Release

variable (SLOW: 100 ms / 1 dB, FAST: 100 ms / 100 dB)

COMPRESSOR SECTION

 

Type

IKA (Interactive Knee Adaptation) compressor

Threshold

variable (-40 dB to +20 dB)

Ratio

variable (1:1 to oo:1)

Threshold characteristics

variable (Interactive or Hard Knee)

Auto characteristics

Wave adaptive compressor

Manual attack time

variable (0.5 ms / 20 dB to 100 ms / 20 dB)

Manual release time

variable (0.05 ms / 20 dB to 5 s / 20 dB)

Auto attack time

typ. 15 ms at 10 dB, 5 ms at 20 dB, 3 ms at 30 dB

Auto release time

program dependent, typ. 125 dB/s

Output

variable (-20 to +20 dB)

 

 

28

8. SPECIFICATIONS

Image 28
Contents Composer PRO Safety Instructions Detailed Safety InstructionsForeword Composer PRO Table of Contents Installation Introduction Before you begin Design conceptControl Elements Expander/gate sectionCompressor section Control elements of the compressor sectionPeak limiter section Control elements of the peak limiter sectionRear panel control elements of the Composer PRO Technical BackgroundNoise as a physical phenomenon What are audio dynamics? Dynamic range capabilities of various devicesCompressors/limiters Expanders/noise-gatesApplications Compression/levelling/limiting/clippingIRC curve characteristic of the Expander Tab .1 Initial settings for the expander/gate section Compressor section IKA characteristic of the compressor section Peak limiter section Tab .3 Initial settings for the peak limiter section Special ApplicationsComposer PRO as a protective device Composer PRO in broadcast Protection of a system with a passive crossoverExternal Side Chain Applications Using an equalizer in the side chain pathSide chain function Tab .1 Initial settings for the De-Esser functions Anticipated compressionInstallation Voice-over compression duckingTriggering additional sounds from a rhythm track Rack mountingSelecting the operating level Balanced use of stereo 1/4 jack plugsSpecifications Audio InputFunction Switches SC Extern Warranty § 1 Warranty CARD/ONLINE Registration
Related manuals
Manual 30 pages 46.7 Kb