Cisco Systems manual Enter a host name for the Cisco VG224

Page 24

Chapter 2 Using the setup Command

Configuring Global Parameters

Would you like to enter the initial configuration dialog? [yes/no]: yes

At any point you may enter a question mark '?' for help.

Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Step 2 When the following message appears, enter yes to begin the initial configuration dialog:

Would you like to enter the initial configuration dialog? [yes/no]:

Note If you answer no to this message, you are prompted to terminate AutoInstall. AutoInstall is a procedure that configures a new Cisco VG224 based on the configuration of an existing Cisco VG224.

If you terminate AutoInstall, you enter the Cisco IOS software CLI.

Note The number of interfaces shown depends on the Cisco VG224.

Step 3 When the following message appears, press Return to see the current interface summary:

First, would you like to see the current interface summary? [yes]:

Any interface listed with OK? value “NO” does not have a valid configuration

Interface

IP-Address

OK?

Method

Status

Protocol

FastEthernet0/0 unassigned

NO

unset

up

down

Step 4 Enter a host name for the Cisco VG224:

Configuring global parameters:

Enter host name [Router]: VG224

The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration.

Step 5 Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when viewing the configuration.

Enter enable secret: xxxx

The enable password is used when you do not specify an enable secret password, with some older software versions, and some boot images.

Step 6 Enter an enable password that is different from the enable secret password. This password is not encrypted (less secure) and can be seen when viewing the configuration.

Enter enable password: guessme

The virtual terminal password is used to protect access to the router over a network interface.

Step 7 Enter the virtual terminal password, which prevents unauthenticated access to the router through ports other than the console port:

Enter virtual terminal password: guessagain

Step 8 Respond to the following prompts as appropriate for your network:

Configure SNMP Network Management? [yes]:

Cisco VG224 Voice Gateway Software Configuration Guide

2-4

OL-5005-01

 

 

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Cisco VG224 Voice Gateway Software Configuration Guide Corporate HeadquartersCisco VG224 Voice Gateway Software Configuration Guide N T E N T S Where to Go Next Command Descriptions C-3 Debugging Commands C-5 OL-5005-01 Objectives AudienceDocument Organization Related and Referenced DocumentsChapter Title Description Cisco Product Document Title Obtaining Documentation Cisco.comDocumentation CD-ROM Ordering DocumentationDocumentation Feedback Obtaining Technical AssistanceCisco TAC Website Opening a TAC Case Obtaining Additional Information TAC Case Priority DefinitionsXiii Xiv Understanding Interface Numbering Cisco IOS Software Basics Identifying the Cisco VG224Port Numbering Conventions Cisco VG224 is used as an example. See -2 onCommand Modes Understanding Cisco IOS Software BasicsGetting Help Undoing a Command or Feature Where to Go Next Saving Configuration ChangesRouter# copy running-config startup-config Upgrading to a New Cisco IOS ReleaseCisco VG224 Voice Gateway Software Configuration Guide Using the setup Command Before Starting Your Cisco VG224Using the setup Command Configuring Global ParametersUsing the setup Command Configuring Global Parameters Configuring global parameters Enter host name Router VG224 Enter a host name for the Cisco VG224Configuring Controller and Interface Parameters Configuring Fast Ethernet and Serial Interface ParametersOptional Configure Chap Configure the Isdn switch type for PRICompleting the Configuration Fast Ethernet Interface ConfigurationAt this point you can proceed to the following OL-5005-01 Configuring with the Command-Line Interface Configuring the Host Name and Password Command PurposeVerifying the Host Name and Password Tip If you are having trouble, ensure the followingConfiguring Fast Ethernet Interfaces Saving Configuration Changes OL-5005-01 Configuring the Voice Interface PrerequisitesRouter# show running-config Router# show startup-configCisco IOS Voice Configuration Library OL-5005-01 Cisco VG224 Configuration Example Appendix a Cisco VG224 Configuration Example Dial-peer voice 6 pots service stcapp Port 2/5 Formatting Procedures Formatting the Compact Flash Memory CardsDetermining the File System on a Compact Flash Memory Card Geometry and format information is displayed in this forma Router# show slot0 allRouter# show flash all Geometry and format information is displayed in this format 11# show flash allRouter# erase slot0 File and Directory Operations Operations for Use with Class B Flash File SystemFormatting Compact Flash Memory as a Class C File System Copying FilesDisplaying the Contents of a Compact Flash Memory Card Delete Files from Compact Flash Memory Router# show slot0Router# dir slot0 Router# delete slot0cvg224-i-mz.tmpDisplaying File Content Operations for Use with Class C Flash File SystemFile Operations for Class C Flash File System Router# more slot0cvg224-i-mzDisplaying Geometry and Format Information Router# show slot0 filesysRename a File Router# delete flashcvg224-i-mz.tmpRouter# rename flashcvg224-i-mz.tmp flashcvg224-i-mz Router# mkdir flash/config Router# mkdir flash/config/test-configDirectory Operations for Class C Flash File System Create a New DirectoryRouter# cd flash/config Router# dir flash Router# rmdir flash/config/test-configRemove a Directory Enter a Directory and Determine Which Directory You AreRouter# cd config PwdDir Router# cd slot0Using the ROM Monitor Entering the ROM Monitor ModeROM Monitor Commands ConfiguringCommand or Action Purpose VerifyingCommand Descriptions Command abcROM Monitor Syntax Conventions Showfpga-Show FPGA-related information Rommon 8 dir flash /dir slot0Debugging Commands Configuration Register CommandsUsing the show rom-monitor command ConfregUsing the upgrade rom-monitor Command Then reload the routerRouter# show rom-monitor Recovering Boot and System Images Using the xmodem CommandUsing the tftpdnld Command Rommon 1 tftpdnldOL-5005-01 Command C-8 Commands Context C-5 Debugging commands C-5dir C-4Timeout Host nameMeminfo Upgrade User Exec command mode
Related manuals
Manual 24 pages 43.46 Kb

VG224 specifications

The Cisco Systems VG224 is a versatile VoIP (Voice over Internet Protocol) gateway designed to facilitate the integration of traditional phone systems with modern IP-based communications. This device plays a crucial role in providing connectivity between analog phones and digital networks, allowing organizations to transition smoothly from legacy telephony systems to IP telephony.

One of the standout features of the VG224 is its ability to support up to 24 analog phone lines. This scalability makes it an ideal choice for small to medium-sized businesses that require a dependable solution to handle their telephony needs without overspending on infrastructure. The VG224 acts as a bridge, converting analog voice signals into digital IP packets, thus enabling seamless communication over the Internet or intranets.

The VG224 is equipped with a range of technologies that enhance its functionality and reliability. Voice activity detection (VAD), comfort noise generation (CNG), and echo cancellation are just some examples of the advanced audio processing techniques integrated into the VG224. These technologies improve call quality by ensuring clear and uninterrupted conversations, even under varying network conditions.

In terms of characteristics, the VG224 features a user-friendly interface with a web-based management console, making it easy for network administrators to configure and manage the device remotely. This streamlined approach to management is crucial for businesses that require quick adjustments to their communication infrastructure without the need for extensive technical knowledge.

The VG224 supports multiple signaling protocols, including H.323, MGCP (Media Gateway Control Protocol), and SIP (Session Initiation Protocol). This flexibility allows it to integrate seamlessly with various IP telephony systems and offers businesses the option to utilize their preferred communication standards. Additionally, the device supports power over Ethernet (PoE), providing the convenience of powering devices through the same cable used for data connectivity, thus reducing the need for additional power sources.

In conclusion, the Cisco Systems VG224 is a robust VoIP gateway that combines advanced technology with user-friendly features. Its capacity to support up to 24 analog lines, along with its compatibility with various signaling protocols, makes it an excellent choice for businesses looking to modernize their telecommunication systems while maintaining the reliability of traditional analog connections. With its ease of management and high-quality voice processing capabilities, the VG224 stands out as a key asset for any organization aiming to optimize its communication infrastructure.
Top Page Image Contents