Cisco Systems VG224 manual Completing the Configuration, Fast Ethernet Interface Configuration

Page 26

Chapter 2 Using the setup Command

Completing the Configuration

•Fast Ethernet Interface Configuration

Fast Ethernet Interface Configuration

This section contains a sample configuration for the Fast Ethernet interface. Enter the values appropriate for your Cisco VG224 and network. The messages you see may vary.

Do you want to configure FastEthernet0/0 interface [yes]:

Use the 100 Base-TX (RJ-45) connector? [yes]:

Operate in full-duplex mode? [no]:

Configure IP on this interface? [no]: yes

IP address for this interface: 6.0.0.1

Number of bits in subnet field [0]:

Class A network is 6.0.0.0, 0 subnet bits, mask is /8

Configure IPX on this interface? [yes]:

IPX network number [1]:

Need to select encapsulation type

[0]sap (IEEE 802.2)

[1]snap (IEEE 802.2 SNAP)

[2]arpa (Ethernet_II)

[3]novell-ether (Novell Ethernet_802.3) Enter the encapsulation type [2]:

Completing the Configuration

When you have provided all the information prompted for by the setup command facility, the configuration appears.

Note For sample configurations, see Appendix A, “Cisco VG224 Configuration Example.”

To complete your configuration, do the following:

Step 1 A setup command facility prompt asks if you want to save this configuration, with the following options:

[0]Go to the IOS command prompt without saving this config.

[1]Return back to the setup without saving this config.

[2]Save this configuration to nvram and exit.

If you answer 0, the configuration information you entered is not saved, and you return to the Cisco VG224 enable prompt (Router#). Type setup to return to the System Configuration Dialog.

If you answer 1, you return to setup without saving the configuration.

If you answer 2, the configuration is saved and you are returned to the user EXEC prompt (Router>).

Step 2 When the messages stop appearing on your screen, press Return to get the Router> prompt.

Step 3 The Router> prompt indicates that you are now at the command-line interface (CLI) and you have just completed a basic Cisco VG224 configuration. However, this is not a complete configuration. At this point you have two choices:

•Run the setup command facility again and create another configuration. Enter the following:

Router> enable

Password: password

Router# setup

Cisco VG224 Voice Gateway Software Configuration Guide

2-6

OL-5005-01

 

 

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Cisco VG224 Voice Gateway Software Configuration Guide Corporate HeadquartersCisco VG224 Voice Gateway Software Configuration Guide N T E N T S Where to Go Next Command Descriptions C-3 Debugging Commands C-5 OL-5005-01 Objectives AudienceChapter Title Description Document OrganizationRelated and Referenced Documents Cisco Product Document Title Documentation CD-ROM Obtaining DocumentationCisco.com Ordering DocumentationCisco TAC Website Opening a TAC Case Documentation FeedbackObtaining Technical Assistance Obtaining Additional Information TAC Case Priority DefinitionsXiii Xiv Understanding Interface Numbering Cisco IOS Software Basics Identifying the Cisco VG224Port Numbering Conventions Cisco VG224 is used as an example. See -2 onGetting Help Command ModesUnderstanding Cisco IOS Software Basics Undoing a Command or Feature Router# copy running-config startup-config Where to Go NextSaving Configuration Changes Upgrading to a New Cisco IOS ReleaseCisco VG224 Voice Gateway Software Configuration Guide Using the setup Command Before Starting Your Cisco VG224Using the setup Command Configuring Global ParametersUsing the setup Command Configuring Global Parameters Configuring global parameters Enter host name Router VG224 Enter a host name for the Cisco VG224Optional Configure Chap Configuring Controller and Interface ParametersConfiguring Fast Ethernet and Serial Interface Parameters Configure the Isdn switch type for PRICompleting the Configuration Fast Ethernet Interface ConfigurationAt this point you can proceed to the following OL-5005-01 Configuring with the Command-Line Interface Configuring the Host Name and Password Command PurposeVerifying the Host Name and Password Tip If you are having trouble, ensure the followingConfiguring Fast Ethernet Interfaces Saving Configuration Changes OL-5005-01 Configuring the Voice Interface PrerequisitesRouter# show running-config Router# show startup-configCisco IOS Voice Configuration Library OL-5005-01 Cisco VG224 Configuration Example Appendix a Cisco VG224 Configuration Example Dial-peer voice 6 pots service stcapp Port 2/5 Determining the File System on a Compact Flash Memory Card Formatting ProceduresFormatting the Compact Flash Memory Cards Router# show flash all Geometry and format information is displayed in this formaRouter# show slot0 all Router# erase slot0 Geometry and format information is displayed in this format11# show flash all Formatting Compact Flash Memory as a Class C File System File and Directory OperationsOperations for Use with Class B Flash File System Copying FilesDisplaying the Contents of a Compact Flash Memory Card Router# dir slot0 Delete Files from Compact Flash MemoryRouter# show slot0 Router# delete slot0cvg224-i-mz.tmpFile Operations for Class C Flash File System Displaying File ContentOperations for Use with Class C Flash File System Router# more slot0cvg224-i-mzDisplaying Geometry and Format Information Router# show slot0 filesysRouter# rename flashcvg224-i-mz.tmp flashcvg224-i-mz Rename a FileRouter# delete flashcvg224-i-mz.tmp Directory Operations for Class C Flash File System Router# mkdir flash/configRouter# mkdir flash/config/test-config Create a New DirectoryRemove a Directory Router# cd flash/config Router# dir flashRouter# rmdir flash/config/test-config Enter a Directory and Determine Which Directory You AreDir Router# cd configPwd Router# cd slot0Using the ROM Monitor Entering the ROM Monitor ModeCommand or Action Purpose ROM Monitor CommandsConfiguring VerifyingROM Monitor Syntax Conventions Command DescriptionsCommand abc Showfpga-Show FPGA-related information Rommon 8 dir flash /dir slot0Debugging Commands Configuration Register CommandsUsing the show rom-monitor command ConfregRouter# show rom-monitor Using the upgrade rom-monitor CommandThen reload the router Recovering Boot and System Images Using the xmodem CommandUsing the tftpdnld Command Rommon 1 tftpdnldOL-5005-01 Timeout Command C-8 CommandsContext C-5 Debugging commands C-5dir C-4 Host nameMeminfo Upgrade User Exec command mode
Related manuals
Manual 24 pages 43.46 Kb

VG224 specifications

The Cisco Systems VG224 is a versatile VoIP (Voice over Internet Protocol) gateway designed to facilitate the integration of traditional phone systems with modern IP-based communications. This device plays a crucial role in providing connectivity between analog phones and digital networks, allowing organizations to transition smoothly from legacy telephony systems to IP telephony.

One of the standout features of the VG224 is its ability to support up to 24 analog phone lines. This scalability makes it an ideal choice for small to medium-sized businesses that require a dependable solution to handle their telephony needs without overspending on infrastructure. The VG224 acts as a bridge, converting analog voice signals into digital IP packets, thus enabling seamless communication over the Internet or intranets.

The VG224 is equipped with a range of technologies that enhance its functionality and reliability. Voice activity detection (VAD), comfort noise generation (CNG), and echo cancellation are just some examples of the advanced audio processing techniques integrated into the VG224. These technologies improve call quality by ensuring clear and uninterrupted conversations, even under varying network conditions.

In terms of characteristics, the VG224 features a user-friendly interface with a web-based management console, making it easy for network administrators to configure and manage the device remotely. This streamlined approach to management is crucial for businesses that require quick adjustments to their communication infrastructure without the need for extensive technical knowledge.

The VG224 supports multiple signaling protocols, including H.323, MGCP (Media Gateway Control Protocol), and SIP (Session Initiation Protocol). This flexibility allows it to integrate seamlessly with various IP telephony systems and offers businesses the option to utilize their preferred communication standards. Additionally, the device supports power over Ethernet (PoE), providing the convenience of powering devices through the same cable used for data connectivity, thus reducing the need for additional power sources.

In conclusion, the Cisco Systems VG224 is a robust VoIP gateway that combines advanced technology with user-friendly features. Its capacity to support up to 24 analog lines, along with its compatibility with various signaling protocols, makes it an excellent choice for businesses looking to modernize their telecommunication systems while maintaining the reliability of traditional analog connections. With its ease of management and high-quality voice processing capabilities, the VG224 stands out as a key asset for any organization aiming to optimize its communication infrastructure.
Top Page Image Contents