Multiquip MT75HS operation manual Operation, Rammer Gearbox and Spring Cylinder Oil Bath

Page 13

OPERATION

This section is intended to assist the operator with the initial start-up of the MT-75HSTamping Rammer.It extremely important that this section be read carefully before attempting to operate the rammer.

DO NOT use your rammer until this section is thoroughly understood.

CAUTION:

Failure to understand the operation of the MT- 75HS Tamping Rammer could result in severe damage to the trowel or personal injury.

Rammer Gearbox and Spring Cylinder Oil Bath

This unit uses an oil bath lubrication system.Perform the following:

1.Check the oil level through the oil level sight glass (Figure 2) at the rear of the tamper foot.

Engine

1.Fill the fuel tank (Figure 3 ) with unleaded gasoline. At the same time, check the engine oil level at the sight gauge located on the operator's side of the oil tank. Fill the oil tank to the "H" level using only outboard (2-stroke) oil. Replenish theoilregularlybeforetheoillevelreachesthe"L"levelofthe oil tank.

CAUTION:

The oil hose is not to be depressed or damaged. A sensor detects lack of oil and shuts down the engine automatically.

Figure 2. Foot Housing Sight Glass

2.If oil is not visible, add 10W-30 motor oil into the oil fill plug opening (Figure 2). The bath contains approximately 1.7 pints (800 cc.)

NOTE

The oil level should be kept at the half way point of the sight glass.

CAUTION:

Failure to understand the operation of the MT- 60HSTamping Rammer could result in severe damage to the rammer or personal injury.

Figure 3. Fuel/Oil Tank

2. Low levels of oil may result in engine seizure due to high levels of consumption during operations.

3. Check the engine oil level (Figure 4) and if the oil level is low, it should be refilled. Use the proper motor oil as suggested in Table 3 .

Figure 4. Engine Oil Dipstick

Table 3. Motor Oil Grade

Season or Temperature

Grade of motor oil

(higher than MS class)

 

 

 

Spring, Summer or Autumn

SAE 30

+120° F to +15° F

 

 

 

Winter

SAE 30

+40° F to +15° F

 

 

 

Below +15° F

SAE 10W-30

 

 

MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) — PAGE 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model MT75HS Proposition 65 Warning MT75HS Rammer Operation and Parts Manual REV. #11 01/12/12 Robin EC-12HS Engine Table of ContentsOrdering parts has never been easier Parts Ordering ProceduresSafety Messages Safety InformationGeneral Safety Engine Safety Transporting Safety Definition of Tamping Rammer General InformationSpecifications MT-75HS Rammer SpecificationsMT-75HS Rammer ComponentsRammer Gearbox and Spring Cylinder Oil Bath OperationFuel Cock and Choke Lever Normal Shutdown Daily MaintenanceFuel and OIL Lines Engine Troubleshooting Symptom Possible Problem Solution TroubleshootingSymptom Possible Problem Solution Explanation of Codes in the Remarks Column Sample Parts ListTo 3 Units To 5 Units Suggested Spare PartsMikasa Nameplate and DecalsPart Name QTY. Remarks Crankcase and Engine Assy Part Name QTY Remarks Guide Cylinder and Foot Assy Piston PIN Tank and Handle Assy Fuel Tank Tank and Handle Assy PACKING, OIL Tank CAP Robin EC12HS Engine Crankcase Assy OIL Seal EC13 Robin EC12HS Engine Crankshaft and Piston Assy Part Name Robin EC12HS Engine Governor Assy Governor Lever Robin EC12HS Engine MUFFLER/AIR Cleaner Assy Muffler Compl Robin EC12HS Engine Carburetor Assy Throttle Valve Robin EC12HS Engine Recoil Starter Assy Cylinder Baffle Robin EC12HS Engine Electric Device Assy Wire 22 CP Robin EC12HS Engine Loose Parts Switch Float CP Freightpolicy Terms and Condition of Sale PartsMT75HS Rammer Operation and Parts Manual REV. #11 01/12/12 HERE’S HOW to GET Help

MT75HS specifications

The Multiquip MT75HS is a versatile and robust machine specifically designed for heavy-duty applications. This innovative piece of equipment is renowned for its reliability and efficiency, making it a popular choice among construction and landscaping professionals. With its unique features and advanced technology, the MT75HS is built to tackle tough tasks with ease.

One of the standout characteristics of the Multiquip MT75HS is its powerful engine. Equipped with a reliable Honda GX390 engine, this machine ensures optimal performance while maintaining fuel efficiency. The engine delivers impressive horsepower, allowing for quick and effective operation, even in challenging conditions. The MT75HS is designed to handle various terrains, making it ideal for both indoor and outdoor applications.

Another significant feature of the MT75HS is its hydraulic drive system, which allows for smooth operation and precise control. This system provides powerful torque that enables the machine to navigate steep inclines and uneven surfaces effortlessly. Additionally, the machine is equipped with high-capacity hydraulic pumps that ensure consistent performance, even under heavy loads.

The MT75HS also boasts an ergonomic design that enhances operator comfort and productivity. It features a spacious operator platform with easy-to-reach controls, reducing fatigue during extended use. The machine’s compact size allows for easy maneuverability in tight spaces, making it perfect for urban construction sites or residential landscaping projects.

Safety is a top priority with the Multiquip MT75HS. It comes equipped with several safety features, including an engine kill switch and a protective roll cage. These elements are crucial in preventing accidents and ensuring the well-being of the operator.

Additionally, the MT75HS offers a variety of attachments, making it an adaptable tool for various tasks. Whether it’s grading, digging, or transporting materials, this machine can be configured to meet specific job requirements. The versatility of the MT75HS makes it a valuable investment for contractors looking to expand their capabilities.

In summary, the Multiquip MT75HS combines power, efficiency, and safety in a compact package. Its advanced features, including a robust engine, hydraulic drive system, ergonomic design, and adaptability, set it apart in the market. For professionals seeking reliability and versatility in their equipment, the MT75HS is an excellent choice that can enhance productivity and tackle a wide range of tasks effectively.
Top Page Image Contents