TABLE OF CONTENTS |
|
|
General Information | page | 2 |
Inventory | page | 2 |
Tools and Building Supplies | page | 2 |
Installation Applications | page | 2 |
Important Safety Information | page | 2 |
Codes | page | 3 |
Combustion and Ventilation Air | page | 3 |
Location of Fireplace | page | 4 |
Clearances | page | 5 |
Preinstallation | page | 5 |
Installation – | page | 5 |
Connecting Gas Line | page | 6 |
Gas Pressure Check | page | 6 |
Electrical Wiring – Optional Blower . page | 7 | |
Finished Wall Details | page | 8 |
Installation – Surround | page | 8 |
Log Assembly | page | 8 |
Flame Appearance | page | 9 |
Optional Equipment | page 10 | |
Forced Air Kit | page 10 | |
Operation and Care | page | 11 |
Cleaning and Servicing | page 11 | |
Replacement Parts | page 11 | |
Accessories/Components | page 12 | |
Appliance Specifications | page 13 | |
CH Operating Instructions | page 14 | |
CM Operating Instructions | page 16 | |
Troubleshooting Guide | page 17 | |
Replacement Parts List | page 18 | |
Replacement Parts | page 19 | |
GENERAL INFORMATION
The VF4000 Series Unvented Room Heaters covered in this manual feature ceramic fiber split logs which glow realistically when the heater is operating.
These heaters are manually controlled. Models
A spark ignition system (piezo) allows the heater pilot gas to be lit without the use of matches or batteries and permits operation of the heater during a power outage.
These heaters are fitted with a specially de- signed pilot (ODS) which responds to the amount of oxygen available in the room and shuts the heater off before the oxygen level drops below 18%. The pilot can be relit only when fresh air is available. Refer to the Com- bustion and Ventilation Air section.
The VF4000 Series Unvented Room Heaters may be built into a framed wall, or installed in an optional oak surround.
This heater has been tested to the standards of ANSI Z21.11.2 unvented heaters.
Do not install these unvented room heaters in a bedroom or bathroom as all units exceed maximum allowable BTU/Hr input of 10,000.
Inventory
Unvented Gas Fireplace Gas connection fittings
Installation and Operating Instructions
Tools and Building Supplies
Normally Required
Tools Should Include:
Phillips screwdriver
Hammer
Saw and/or Sabersaw
Measuring tape
Electric drill and bits
Pliers
Square
Piping complying with local codes
Pipe wrench
Tee joint
Pipe compound
Building Supplies Should Include:
Framing materials Wall finishing materials
Caulking materials (noncombustible) Fireplace surround materials
Installation Applications
1.Fireplace built into a framed wall.
2.Fireplace installed with oak surround and/ or platform (Refer to the
Check the inventory list to be sure that you have all the necessary parts in usable condition. Also check for concealed damage.
IMPORTANT SAFETY INFORMATION
INSTALLER: PLEASE LEAVE THESE INSTRUC- TIONS WITH THE OWNER.
OWNER: PLEASE RETAIN THESE INSTRUC- TION FOR FUTURE REFERENCE.
IMPORTANT: BEFORE STARTING YOUR HEATER INSTALLATION, READ THESE INSTAL- LATION INSTRUCTIONS CAREFULLY TO BE SURE YOU UNDERSTAND THEM COMPLETELY AND IN ENTIRETY. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD CAUSE A HEATER MALFUNCTION RESULTING IN SERI- OUS INJURY AND/OR PROPERTY DAMAGE.
WARNING: THESE APPLIANCES ARE DESIGNED TO OPERATE ON NATURAL OR PROPANE GAS ONLY. THE USE OF OTHER FUELS OR COMBINATION OF FUELS WILL DEGRADE THE PERFOR- MANCE OF THIS SYSTEM AND MAY BE DANGEROUS.
2
UNVENTED GAS ROOM HEATER SPECIFICATIONS AND TECHNICAL DETAILS
|
|
|
| Valve |
| Regulator Pressure | Gas Inlet |
Model No. | Gas Type | Maximum BTU/HR | Operation | Ignition | Setting | Pressure | |
|
|
|
|
|
|
| |
Natural | 25,000 | Manual | Piezo | 5" w.c. | Max 10 ¹⁄₂" w.c. | ||
|
|
|
|
|
| Min. 6" w.c. | |
|
|
|
|
|
|
| |
Propane/ | 25,000 | Manual | Piezo | 10" w.c. | Max 13" w.c. | ||
LPG |
|
|
|
|
| Min. 11" w.c. | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|