Heat & Glo LifeStyle 36DV manual Vent Termination, Sitioned SO That the Arrow is Pointing UP

Page 17

For Vertical Runs - One ceiling firestop is REQUIRED at the hole in each ceiling through which the vent passes.

To install firestops for vertical runs that pass through ceilings:

•Position a plumb bob directly over the center of the verti- cal vent component.

•Mark the ceiling to establish the centerpoint of the vent.

•Drill a hole or drive a nail through this centerpoint.

•Check the floor above for any obstructions, such as wir- ing or plumbing runs.

•Reposition the fireplace and vent system, if necessary, to accommodate the ceiling joists and/or obstructions.

•Cut an 10-inch X 10-inch (254mm X 254mm) hole through the ceiling, using the centerpoint previously marked.

•Frame the hole with framing lumber the same size as the ceiling joists.

10" (254mm)

10" (254mm)

 

 

CHIMNEY

 

HOLE

NEW

EXISTING CEILING

JOISTS

FRAMING

 

MEMBERS

 

CEILING

 

Figure 16. 10" x 10" Hole & New Framing Members

If the area above the ceiling is NOT an attic, position and secure the ceiling firestop on the ceiling side of the previously cut and framed hole.

NOTE: There must be NO INSULATION or other combustibles inside the framed firestop opening.

JOIST

CEILING

NAILS (4 REQUIRED)

CEILING FIRESTOP

Figure 17. Ceiling Firestop (Ceiling Side)

If the area above the ceiling IS an attic, position and secure the firestop on top of the previously framed hole.

NOTE: Keep insulation away from the vent pipe at least 1 inch (25mm).

NAILS (4 REQUIRED)

 

RAFTER

CEILING

CEILING FIRESTOP

Figure 18.

Attic Firestop

C. Vent Termination

For Horizontal Terminations - To attach and secure the termination to the last section of horizontal vent refer to the Cinch Pipe and Termination Cap installation instructions.

•Push and snap-lock the ends as described at the begin- ning of the Installing Vent Components section.

•The termination kit should pass through the wall firestops from the exterior of the building.

•Adjust the termination cap to its final exterior position on the building.

WARNING: THE TERMINATION CAP MUST BE PO-

!SITIONED SO THAT THE ARROW IS POINTING UP.

For trapezoidal cap termination kits:

•Using screws secure the cap to the exterior wall through the flanges in the cap.

!WARNING: VENTING TERMINALS SHALL NOT BE RECESSED INTO A WALL OR SIDING. VENT

TERMINATION CLEARANCES MUST BE FOLLOWED TO AVOID FIRE DANGER. SEE VENT TERMINATION MINIMUM CLEARANCES DIAGRAM ON NEXT PAGE.

7 1/4” (184mm)

Figure 19. Trapezoid Termination Cap

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents What to do if you smell gas Installers GuideSafety and Warning Information Table of Contents ESCAPE-36DV Log set assemblyESCAPE-36DV Service Parts List / Liste des pièces de rechangeHigh Altitude Installations Installation CodesAppliance Certification CertificationANY Such Action MAY Possibly Cause a Fire Hazard Pre-install PreparationIntroducing the Heat-N-Glo Gas Fireplaces Diagram of the ESCAPE-36DV Clearance Requirements Constructing the Fireplace ChaseLocating the Fireplace Clearance to Hearth Extension Framing the FireplaceAT Each Joint Vent System Approvals Installing the Vent SystemTems or Components MAY be Used Identifying Vent ComponentsMAX .4 M Straight Up Vertical Venting Vertical VentingVenting with One 90 Elbow Venting with ONE 1 90 Elbow+ H Venting with Three 3 90 ElbowsInstall Support Brackets Installing Vent ComponentsVenting Out the Top Vent Attach the First Vent Component to the Starting CollarsSitioned SO That the Arrow is Pointing UP Vent TerminationVent Termination Minimum Clearances Leveling and Securing of a Fireplace Positioning, Leveling Securing the FireplaceVice Must be Wired Directly to the FIRE- Place Junction BOX Installing the Optional Heat-Zone KitHeat-Zone Kit Gas Control SystemCheck for GAS Leaks Gas Supply LineGas Pressure Requirements Wiring the Fireplace LET/OUTLET Grilles in ANY Manner FinishingPlacing the Ember Material Positioning the Logs Placing the Ember MaterialPositioning the Logs Double-check for faulty components After the InstallationBefore Lighting the Fireplace Lighting the FireplaceImportant Turn OFF the GAS Before Servicing Your Fireplace Fireplace Maintenance
Related manuals
Manual 58 pages 12.02 Kb

36DV specifications

The Heat & Glo LifeStyle 36DV is a state-of-the-art gas fireplace designed for modern living spaces. This model stands out for its seamless blend of aesthetics, performance, and efficiency. With its sleek design and innovative technologies, the LifeStyle 36DV redefines how people experience warmth and ambiance in their homes.

One of the standout features of the LifeStyle 36DV is its powerful heating capability. This direct vent gas fireplace efficiently circulates warm air throughout the room while maintaining optimal energy usage. With an impressive heating output, it can effectively warm spaces of varying sizes, making it suitable for both large living areas and cozy nooks.

The LifeStyle 36DV is engineered with advanced gas technology. The fireplace utilizes a unique ignition system that ensures reliable starts and consistent performance. This system not only enhances ease of use but also increases safety, minimizing any risks associated with traditional ignition methods.

Additionally, the fireplace is equipped with a dynamic, glass-front design that maximizes the viewing area of the flames. With a variety of media options available, including traditional logs and modern glass media, homeowners can customize the look and feel of their fireplace to match their unique style. The LifeStyle 36DV can serve as a focal point in any room, providing both warmth and visual appeal.

Another noteworthy characteristic of the LifeStyle 36DV is its intuitive control system. With the ability to operate via remote control, wall switch, or smartphone app, adjusting the fireplace's settings has never been easier. Users can effortlessly change the flame height, control fan speed, and set timers, allowing for a personalized experience tailored to individual preferences.

The energy efficiency of the LifeStyle 36DV also cannot be overlooked. This fireplace is designed to meet stringent environmental standards, providing homeowners with a cost-effective heating solution that doesn't compromise on style. By utilizing innovative insulation and venting technology, the LifeStyle 36DV keeps the warmth inside where it belongs.

In summary, the Heat & Glo LifeStyle 36DV is a remarkable gas fireplace offering a perfect combination of modern technology and traditional warmth. With its stylish design, powerful heating capabilities, customizable aesthetics, and user-friendly controls, it stands out as a premier choice for homeowners looking to enhance their living spaces. Whether for cozy family gatherings or romantic evenings, the LifeStyle 36DV provides an inviting atmosphere that is hard to match.
Top Page Image Contents