Heat & Glo LifeStyle 36DV manual Positioning the Logs Placing the Ember Material

Page 24

Facing Requirements

When finishing the front of the fireplace, combustible mate- rial must never overlap into the face of the unit.

There are two different ways the unit can be set and fin- ished. Figure 28 shows the fireplace face flush with the wall covering material. In this case a 12” piece of non-combus- tible material must be placed above the fireplace, see Fig- ure 27 (top). Use the nailing tabs that are set back 1/2”.

COMBUSTIBLE

O.K.

Figure 28.

The second way the fireplace can be set and finished is to cover the entire face of the fireplace with non-combustible material, see Figure 27 (bottom). In this case the fireplace is set flush with the stud, see Figure 29. Use the forward set of nailing tabs.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COMBUSTIBLE

Figure 29.

 

NON-COMBUSTIBLE

 

O.K.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

No matter what method is used, the finishing material must NEVER pass the 1/2” metal edge around the opening and overhang into the glass opening.

!WARNING: FACING AND/OR FINISHING MA- TERIAL MUST NEVER OVERHANG INTO THE GLASS OPENING.

Step 11. Positioning the Logs,

and Placing the Ember Material

Positioning the Logs

If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately, refer to the instructions that accompany the logs. Save the log instructions with this manual.

If sooting occurs, the logs might need to be repositioned slightly to avoid excessive flame impingement.

Placing the Ember Material

Ember material is shipped with this gas fireplace. To place the ember material:

•Remove the ash lip that is located in front of the glass.

•Remove the side panels that are located in front of the glass.

•Remove the pull mesh firescreen by unhooking from the fireplace.

•Pull and release the four glass latches (2 per side) lo- cated on the sides of the glass frame.

•Grasping the upper lip with one hand and the lower lip with the other, pull the bottom of the glass out first. Guide the bottom while letting the top drop down under the top of the opening (see Figure 30).

UPPER

LIP

GLASS

CLIP

Figure 30. Glass Assembly

Glass Specifications: ESCAPE-36DV: CERAMIC

•There are two types of ember shipped with the unit. Plati- num Embers for the burner surface and Mystic Embers for the floor of the unit.

•Do NOT place Platinum Embers between log #3 and log #4. They may disrupt the flames and are not visible.

•Place Mystic Embers on the floor of the unit. Use the Mystic Embers to hide the pilot wires on the left side of the burner.

•Save the remaining ember materials for use during fire- place servicing.

•Replace the glass firescreen and door front trim on the unit.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Installers Guide What to do if you smell gasSafety and Warning Information Table of Contents Log set assembly ESCAPE-36DVService Parts List / Liste des pièces de rechange ESCAPE-36DVInstallation Codes High Altitude InstallationsAppliance Certification CertificationPre-install Preparation Introducing the Heat-N-Glo Gas FireplacesANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the ESCAPE-36DV Constructing the Fireplace Chase Locating the FireplaceClearance Requirements Framing the Fireplace Clearance to Hearth ExtensionAT Each Joint Installing the Vent System Vent System ApprovalsTems or Components MAY be Used Identifying Vent ComponentsVertical Venting MAX .4 M Straight Up Vertical VentingVenting with ONE 1 90 Elbow Venting with One 90 ElbowVenting with Three 3 90 Elbows + HInstalling Vent Components Install Support BracketsVenting Out the Top Vent Attach the First Vent Component to the Starting CollarsVent Termination Sitioned SO That the Arrow is Pointing UPVent Termination Minimum Clearances Positioning, Leveling Securing the Fireplace Leveling and Securing of a FireplaceInstalling the Optional Heat-Zone Kit Vice Must be Wired Directly to the FIRE- Place Junction BOXHeat-Zone Kit Gas Control SystemGas Supply Line Gas Pressure RequirementsCheck for GAS Leaks Wiring the Fireplace Finishing LET/OUTLET Grilles in ANY MannerPositioning the Logs Placing the Ember Material Positioning the LogsPlacing the Ember Material After the Installation Double-check for faulty componentsBefore Lighting the Fireplace Lighting the FireplaceFireplace Maintenance Important Turn OFF the GAS Before Servicing Your Fireplace
Related manuals
Manual 58 pages 12.02 Kb

36DV specifications

The Heat & Glo LifeStyle 36DV is a state-of-the-art gas fireplace designed for modern living spaces. This model stands out for its seamless blend of aesthetics, performance, and efficiency. With its sleek design and innovative technologies, the LifeStyle 36DV redefines how people experience warmth and ambiance in their homes.

One of the standout features of the LifeStyle 36DV is its powerful heating capability. This direct vent gas fireplace efficiently circulates warm air throughout the room while maintaining optimal energy usage. With an impressive heating output, it can effectively warm spaces of varying sizes, making it suitable for both large living areas and cozy nooks.

The LifeStyle 36DV is engineered with advanced gas technology. The fireplace utilizes a unique ignition system that ensures reliable starts and consistent performance. This system not only enhances ease of use but also increases safety, minimizing any risks associated with traditional ignition methods.

Additionally, the fireplace is equipped with a dynamic, glass-front design that maximizes the viewing area of the flames. With a variety of media options available, including traditional logs and modern glass media, homeowners can customize the look and feel of their fireplace to match their unique style. The LifeStyle 36DV can serve as a focal point in any room, providing both warmth and visual appeal.

Another noteworthy characteristic of the LifeStyle 36DV is its intuitive control system. With the ability to operate via remote control, wall switch, or smartphone app, adjusting the fireplace's settings has never been easier. Users can effortlessly change the flame height, control fan speed, and set timers, allowing for a personalized experience tailored to individual preferences.

The energy efficiency of the LifeStyle 36DV also cannot be overlooked. This fireplace is designed to meet stringent environmental standards, providing homeowners with a cost-effective heating solution that doesn't compromise on style. By utilizing innovative insulation and venting technology, the LifeStyle 36DV keeps the warmth inside where it belongs.

In summary, the Heat & Glo LifeStyle 36DV is a remarkable gas fireplace offering a perfect combination of modern technology and traditional warmth. With its stylish design, powerful heating capabilities, customizable aesthetics, and user-friendly controls, it stands out as a premier choice for homeowners looking to enhance their living spaces. Whether for cozy family gatherings or romantic evenings, the LifeStyle 36DV provides an inviting atmosphere that is hard to match.
Top Page Image Contents