Majestic Appliances EWF36A Installating Outside Air Kit, Installation Precautions

Page 11

Nail Top

Standoffs

Nail Side

Nailing

Flanges

Vermont Castings EWF36A

Duct run must be limited to a maximum distance of 40 feet from the fireplace pipe collar to duct termination. This will provide the least restriction to air flow. No more than four (4) 90° elbows can be used. Duct run may be horizontal, vertical, inclined or any combination of these. Vertical duct runs must be at least three (3) feet below the fireplace chimney flue exit. (Fig. 13) You are now ready to install the AK-MST Outside Air Kit.

FP1197

Fig. 12 Fasten fireplace in position.

Installating Outside Air Kit

An outside air kit may be installed on the EWF36A. If desired, or if local codes mandate the use of an air kit, then two (2) AK-MSTs are required to complete the installation (from air kit to the outdoors). If the outside air kits are to be used, the AK-MSTs MUST be installed BEFORE the fireplace is enclosed.

Duct Termination Must be More Than 3’ Below Chimney

Duct

Termination

40’ Max.

Duct Run

Attic

Ceiling

Duct

NOTE: Four (4) inch Class 1 air duct, material or metal duct (not supplied) may be used with AK-MST. (For installation in New York State, only aluminum, noncombustible flexible or type “O” metal ducting is permissible.)

Installation Precautions

Soffit Termination

The duct termination should be located so it is exposed to an out-of-doors opening at least 100 square inches. If the duct termination must be located in a crawl space or basement, be sure the termination area has 100 square inches of ventilation opening to outside air.

The duct termination must be located so it does not compete for air flow with exhaust fans, gas vent hoods or other air consuming devices or appliances. It must not be obstructed by rafters, insulation materials or other obstructions. The less restrictive the air supply, the better the AK-MST will perform.

Exterior Wall

Rain Cap

Duct

Termination

40’ Max. Duct Run

Duct

It is a good practice to protect your hands and eyes during installation by wearing work gloves and safety glasses.

CAUTION: Do not install termination into a garage or other area that could contain flammable liquids or fumes, or into an attic space.

Installation Instructions

Determine the location of the fireplace as described in the fireplace Installation Manual. Then plan location of the duct termination and the route of the duct run between the fireplace and the duct termination.

Exterior Wall Termination

FP1060

Fig. 13 Typical installations.

1.Remove and discard the outside air cover plate located at the center of both sides of the fireplace. Use care not to rub against the sharp edges of this opening to avoid cuts. Remove the four (4) screws exposed when cover plate is removed. Retain for future use.

2.Slide the two (2) connecting boxes provided with the unit into the openings on each side of the unit.

3.Attach the connecting boxes to the inside panel with four (4) screws removed in Step 1.

20005167

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents EWF36A Introduction Table of ContentsDrafts Safety InformationPrecautions DescriptionEWF36A Woodburning Fireplace SpecificationsFireplace and chase parts identification Chase InstallationSupport Chimney Requirements Offset InstallationsTen Foot Rule Planning InformationMounting the Fireplace Planning the Chimney RunInsulating Fireplace Enclosure for Cold Climates InstallationChimney Supports EB1 Receptacle Hookup Straight-Up Chimney InstallationOffset Installation FramingFraming the Ceiling Hole Positioning, Safety Strips Securing the FireplaceCeiling Chimney Hole Possible Obstructions Cutting the HoleInstallation Instructions Installating Outside Air KitInstallation Precautions Proper Firestop Spacer Installation Installing the Chimney SystemInstalling the Firestop Spacer Ceiling Hole Canadian Requirements For Insulation Shield Continue Installing Pipe to Complete RunAdditional Ceilings Penetrating the RoofFinishing Finish Wall Install Remainder of Chimney SectionsInstall Top Housing or Termination Installing Chimney in a ChaseExamples of wall shield insulation Hearth InstallationMantels Side Wall ProtectionCommon Materials and Factors Minimum Wall Clearances Primary Air Control OperationAttach Handles EWF36A ControlsBurn Only High-Quality Wood Use the Air Control Settings That Work Best for YouFan Glass DoorsSpecial Tactics for Cold-Climate Heating Starting and Maintaining a Wood FireReloading and Reviving a Wood Fire Remove and Store Ash Safely Maintenance Inspecting the Combustor When to Suspect a Combustor ProblemRemoving, Cleaning or Replacing the Combustor How to Replace GasketsReplace Damaged Door Glass Immediately Clean Chimney System is Safer and Works BetterChimney System Replacing the Door GasketsFireplace Daily Maintenance ScheduleYearly Spring Cleaning Component Description Model Number Chimney ComponentsEWF36A Fireplace EWF36A Fireplace Screen Kit Optional AccessoriesFan Kit Trim KitsWarranty

EWF36A specifications

Majestic Appliances EWF36A is a sophisticated and highly efficient electric wall furnace designed to provide optimal heating solutions for both residential and commercial spaces. Known for its sleek design and powerful performance, the EWF36A ensures an effective heating experience during cold seasons while maintaining energy efficiency.

One of the standout features of the EWF36A is its cutting-edge quartz heating technology. Unlike traditional heating methods, quartz heaters offer rapid warmth, as they produce infrared heat that instantly penetrates the air and warms up objects and people within the room. This technology not only enhances comfort but also minimizes heat loss, making the EWF36A a cost-effective option for heating your space.

The EWF36A operates with a user-friendly thermostat control, allowing individuals to easily adjust temperatures to their liking. This feature grants users full control over their heating environment, providing a tailored experience that can be fine-tuned for maximum comfort. Additionally, the unit offers multiple heating settings, making it suitable for various room sizes and heating needs.

With a focus on safety, the Majestic EWF36A is equipped with an automatic shut-off feature that activates when the unit overheats. This ensures peace of mind and adds an extra layer of protection, particularly in homes with children or pets. Furthermore, the furnace’s exterior is constructed from durable materials, designed to withstand the test of time and provide reliable performance season after season.

The EWF36A also boasts a quiet operation mode, enabling it to function without causing disruptions, making it ideal for bedrooms, offices, or any quiet space. It blends seamlessly into modern interiors, thanks to its stylish and compact design that can be mounted on walls or placed in corners.

In terms of efficiency, the EWF36A utilizes minimal energy compared to traditional heating systems, which translates to reduced electricity bills. Its eco-friendly design aligns with contemporary sustainability efforts, ensuring that users can enjoy warmth without compromising on environmental values.

In conclusion, the Majestic Appliances EWF36A combines innovation, efficiency, and aesthetic appeal, making it a top choice for anyone seeking reliable and effective heating solutions. Its advanced features, user-friendly controls, and robust safety measures position it as a leading option in the electric heating market.
Top Page Image Contents