Majestic Appliances EWF36A Additional Ceilings, Penetrating the Roof, Cut and Frame Roof Hole

Page 13

If the area above the ceiling is not an attic, position the firestop spacer with the flange on the ceiling side and the angled portion extending up into the hole.

If the area above the ceiling is an attic, position the firestop spacer with the flange on the top of the framed hole and the angled portion extending down into the hole.

Firestop spacers are not available for, nor are they required on vertical walls.

DO NOT put any sealant around the area where the outer pipe slides through the firestop spacer. If you seal this area, it may cause a fire hazard.

Attic Installation

Nails (4)

Firestop Spacer

Joist

Ceiling Installation

Joist

Firestop Spacer

Vermont Castings EWF36A

Attic Insulation

Shield

Nails

(4 Required)

Attic Joist

 

Base

Ceiling

Flanges

FP263

 

Fig. 18 Attic shield installation (Canadian requirement).

Chimney Supports

If chimney supports are required, they are installed the same as elbows. Nail chimney support straps to adjacent structural framing, as shown on Figure 16. Bend straps as necessary and make sure they are secure so they will support the weight of the chimney. A chimney support is 2¹⁄₂" (64mm) long when installed. Consider this dimension when determining how many straight chimney sections are needed.

NOTE: Chimney supports are generally used in long runs in a chase installation.

Additional Ceilings

If you encounter additional ceilings, repeat same steps required for first ceiling installation. See firestop illustration in Figure 17.

Nails (4)

Fig. 17 Firestop spacer installations.

FP593

Penetrating the Roof

Run pipe to roofline. Since chimney system must be vented to the out-of-doors, you must use an approved Vermont Castings, Majestic Products termination.

Canadian Requirements

for Insulation Shield

In Canada, an attic insulation shield is required to prevent attic insulaiton from contacxting the chimney section. Framing dimensions fr the chimney hole should measure 17¹⁄₂” x 17¹⁄₂” (445mm x 445mm). An attic shield MUST be installed on top of attic joists (above the floor level). (Fig. 18)

Continue Installing Pipe to Complete Run

Continue attaching pipe sections to complete system to next level always being careful that the pipe is firmly snapped locked in place before proceeding to next pipe section.

If a chase is used, refer to the installation manual provided with the termination cap.

Locate Chimney Centerpoint on Roof

Use same procedure detailed in locating center point of the flue system.

Drive a nail up through roof at the center point. This will determine center point on outside of the roof.

Cut and Frame Roof Hole

Size of roof hole varies with the type of chimney termi- nation installed. Refer to installation instructions provided with Vermont Castings, Majestic Products chimney termination to find correct size of roof hole.

20005167

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents EWF36A Introduction Table of ContentsPrecautions Safety InformationDescription DraftsEWF36A Woodburning Fireplace SpecificationsFireplace and chase parts identification Chase InstallationSupport Chimney Requirements Offset InstallationsMounting the Fireplace Planning InformationPlanning the Chimney Run Ten Foot RuleChimney Supports InstallationInsulating Fireplace Enclosure for Cold Climates Offset Installation Straight-Up Chimney InstallationFraming EB1 Receptacle HookupCeiling Chimney Hole Possible Obstructions Positioning, Safety Strips Securing the FireplaceCutting the Hole Framing the Ceiling HoleInstallation Precautions Installating Outside Air KitInstallation Instructions Installing the Firestop Spacer Ceiling Hole Installing the Chimney SystemProper Firestop Spacer Installation Additional Ceilings Continue Installing Pipe to Complete RunPenetrating the Roof Canadian Requirements For Insulation ShieldInstall Top Housing or Termination Install Remainder of Chimney SectionsInstalling Chimney in a Chase Finishing Finish WallMantels Hearth InstallationSide Wall Protection Examples of wall shield insulationCommon Materials and Factors Minimum Wall Clearances Attach Handles OperationEWF36A Controls Primary Air ControlFan Use the Air Control Settings That Work Best for YouGlass Doors Burn Only High-Quality WoodReloading and Reviving a Wood Fire Starting and Maintaining a Wood FireSpecial Tactics for Cold-Climate Heating Remove and Store Ash Safely Maintenance Removing, Cleaning or Replacing the Combustor When to Suspect a Combustor ProblemHow to Replace Gaskets Inspecting the CombustorChimney System Clean Chimney System is Safer and Works BetterReplacing the Door Gaskets Replace Damaged Door Glass ImmediatelyYearly Spring Cleaning Maintenance ScheduleFireplace Daily Component Description Model Number Chimney ComponentsEWF36A Fireplace EWF36A Fireplace Fan Kit Optional AccessoriesTrim Kits Screen KitWarranty

EWF36A specifications

Majestic Appliances EWF36A is a sophisticated and highly efficient electric wall furnace designed to provide optimal heating solutions for both residential and commercial spaces. Known for its sleek design and powerful performance, the EWF36A ensures an effective heating experience during cold seasons while maintaining energy efficiency.

One of the standout features of the EWF36A is its cutting-edge quartz heating technology. Unlike traditional heating methods, quartz heaters offer rapid warmth, as they produce infrared heat that instantly penetrates the air and warms up objects and people within the room. This technology not only enhances comfort but also minimizes heat loss, making the EWF36A a cost-effective option for heating your space.

The EWF36A operates with a user-friendly thermostat control, allowing individuals to easily adjust temperatures to their liking. This feature grants users full control over their heating environment, providing a tailored experience that can be fine-tuned for maximum comfort. Additionally, the unit offers multiple heating settings, making it suitable for various room sizes and heating needs.

With a focus on safety, the Majestic EWF36A is equipped with an automatic shut-off feature that activates when the unit overheats. This ensures peace of mind and adds an extra layer of protection, particularly in homes with children or pets. Furthermore, the furnace’s exterior is constructed from durable materials, designed to withstand the test of time and provide reliable performance season after season.

The EWF36A also boasts a quiet operation mode, enabling it to function without causing disruptions, making it ideal for bedrooms, offices, or any quiet space. It blends seamlessly into modern interiors, thanks to its stylish and compact design that can be mounted on walls or placed in corners.

In terms of efficiency, the EWF36A utilizes minimal energy compared to traditional heating systems, which translates to reduced electricity bills. Its eco-friendly design aligns with contemporary sustainability efforts, ensuring that users can enjoy warmth without compromising on environmental values.

In conclusion, the Majestic Appliances EWF36A combines innovation, efficiency, and aesthetic appeal, making it a top choice for anyone seeking reliable and effective heating solutions. Its advanced features, user-friendly controls, and robust safety measures position it as a leading option in the electric heating market.
Top Page Image Contents