Vanguard Heating 000 to 26, VMH26TPC, VMH26TNC Product Features, Unpacking, Assembly

Page 5

PRODUCT FEATURES

SAFETY PILOT

This fireplace has a pilot with an Oxygen Deple- tion Sensing (ODS) safety shutoff system. The ODS/pilot is a required feature for vent-free room fireplaces. The ODS/pilot shuts off the fireplace if there is not enough fresh air.

PIEZO IGNITION SYSTEM

This fireplace has a piezo ignitor. This system re- quires no matches, batteries, or other sources to light fireplace.

THERMOSTATIC HEAT CONTROL

This fireplace has a thermostat sensing bulb and a control valve. The thermostat will automatically modulate the heat output to maintain a consistent room temperature. This results in greater fireplace comfort. This can also result in lower gas bills.

UNPACKING

1.Remove fireplace and hood from carton. Log is wrapped and inside fireplace. Do not re- move at this time.

2.Remove all protective packaging applied to fireplace for shipment.

3.Make sure your fireplace includes one hard- ware packet.

4.Check fireplace for any shipping damage. If fireplace is damaged, promptly inform dealer where you bought fireplace.

ASSEMBLY

WARNING: Always have branch support and screen in place before operating fireplace. This prevents excessive tem- peratures on fireplace surfaces.

WARNING:Failuretoposition thepartsinaccordancewiththese diagrams or failure to use only parts specifically approved with this fireplace may result in prop- erty damage or personal injury.

ASSEMBLING FIREPLACE

Tools Required:

Phillips screwdriver

5/16" hex wrench

slotted screwdriver

Installing Log

1.Lift screen up and pull out to remove.

2.Cut two plastic straps to remove the log from the firebox cavity.

3.An optional blower is available. See Accessories, page 30. Install optional blower now. Follow in- stallation instructions provided with blower.

4.Remove log packaging material and discard packaging. Gently place log set on burner sup- port (see Figure 2). The log should fit flat against top of burner support and log locator tabs fit into the slots under the log. Do not allow log to contact flame. If flame contacts log, soot will be created.

Log Shoulder

Screw

Burner Support with Log Locator Tabs

Branch

Support

Screen

Figure 2 - Assembling Fireplace

113111-01A

www.desatech.com

5

Image 5
Contents What to do if YOU Smell GAS Shown with Optional Cabinet Mantel/Hearth Base AccessoryTable of Contents Safety Information Product Identification Local CodesUnpacking Product FeaturesAssembly Providing Adequate Ventilation AIR for Combustion VentilationAssembling Hood Unusually Tight ConstructionDetermining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Fireplace LocationConfined and Unconfined Space Ventilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Check GAS Type InstallationInstallation Items Locating Fireplace BUILT-IN Fireplace InstallationRough Opening for Installing Wall Mantel Clearances for Built-In Installation Optional Mantel InstallationRemoving Upper Louver Assembly Installing Blower Accessory GA3450TAssembling Perimeter Trim Trim Shipped with Mantel Removing Valve Cover ShieldRemoving Valve Cover Shield Installing Blower AssemblyFor Built-In Installation Installing Switch Plate to Valve Cover ShieldExtension Cord Connecting to GAS SupplyAttaching Wood Base to Solid Floor Installation Items Needed Connecting Equipment Shutoff Valve to Heater ControlChecking GAS Connections Pressure Testing Gas Supply Piping SystemPressure Testing Fireplace Gas Connections Lighting Instructions For Your Safety Read Before LightingOperating Fireplace To Turn OFF GAS To Appliance Manual Lighting ProcedureThermostat Control Operation Shutting Off FireplaceOperating Blower Inspecting BurnerBurner Flame Pattern Pilot Flame PatternBurner Injector Holder and Pilot AIR Inlet Hole Cleaning MaintenanceCabinet Air PassagewaysObserved Problem Possible Cause Remedy TroubleshootingSee Cleaning and Mainte Residues from manufacturing Statement above Gas leak. See WarningService Hints SpecificationsTechnical Service Replacement PartsIllustrated Parts Breakdown Parts List Accessories Corner Mantel with Full Hearth Base Cleaning KIT GCKCabinet Mantel and Full Hearth Base Information VideoLimited Warranty VENT-FREE Compact Classic Hearth Fireplace Warranty InformationKeep this Warranty