Outside AIR KIT Installation | Desa (V)3612ST specification

OUTSIDE AIR KIT INSTALLATION GAS LINE INSTALLATION

OUTSIDE AIR KIT

INSTALLATION

The installation of the outside air kit must be installed during the rough framing of the fireplace due to the nature of its location. Outside combustion air can be accessed through an exterior wall or a vented crawl space (see Figure 13).

CAUTION: Air inlet ducts must not terminate in attic space.

The maximum height for the air inlet above the platform of fireplace is a minimum of 3 feet below the chimney cap.

For further details on the installation of the outside air kit, please refer to the instructions included with the air kit.

Secure Two Collars With

Duct Tape or ScrewsAir Inlet Termination

Air Inlet

Location

Must Allow

For Bushes

Or Snow

FOR UNVENTED ROOM HEATERS, ANSI\IAS\AGA Z21.11.2,

ARE TO BE INSTALLED IN THIS FIREPLACE.

1.To install, remove the knockout indentation on the refractor (or firebrick) wall located approximately 2 inches above the refractory hearth floor. The knockout indentation must be firmly tapped with any solid object until it is released. Remove frag- mented portion of refractory (see Figure 14).

2.Remove gas line cover plate on rear of fireplace and pull out insu- lation from gas line conduit sleeve, save insulation for reuse.

3.Run gas line into the fireplace through the rear at 111/4" from the floor and through gas line conduit sleeve (if using a raised platform, add height). Provide sufficient gas line into fireplace chamber for fitting connection (see Figure 15).

Note: Secure incoming gas line to wood framing to provide rigidity for threaded end.

4.Repack insulation around gas line and into sleeves openings. Seal any gaps between gas line and refractory knockout hole with refractory cement or commercial furnace cement. Install the decorative gas appliance or cap off gas line if desired.

Figure 13 - Air Kit Installation

GAS LINE INSTALLATION

WARNING: A qualified service person must con- nect fireplace to gas supply. Follow all local codes.

Outside of Fireplace

Remove

Insulation

Temporarily

(Do Not

Discard)

Gas Line

Conduit

Remove

Knockout

Replace Screws After

Removing Gas Line

Cover Plate

Side Firebrick Finished Side

Refractory Knockout Plug, Remove by Tapping Lightly With A 1/2" Dowel

NOTICE: BEFORE YOU PROCEED, MAKE SURE YOUR GAS SUPPLY IS OFF!

A gas line may be installed for the purpose of installing a vented or vent-free decorative gas appliance available through your local distributor. Use only gas piping approved by local codes. When installing a gas line, a shutoff valve designed for installation outside the appliance is recommended.

The gas pipe is intended for connection to a decorative gas appliances that operate from natural or propane/LP fuel only: (1), incorporating an automatic shutoff device and, (2), complying with the Standard for

Decorative Gas Appliances for Installation in Vented Fireplace, ANSI Z21.60-1990. ONLY UNVENTED GAS LOG SETS WHICH HAVE BEEN FOUND TO COMPLY WITH THE STANDARD

Figure 14 - Removing Knockout for Gas Line Installation

Side Firebrick

Outside ofFinished Side

Fireplace

Gas Line	Incoming	Provide Enough
	1/2" Black
Conduit		Threaded End For
	Iron Pipe
		Fitting Connection

Repack

InsulationSeal Opening

With Refractory

Cement

Figure 15 - Running Gas Line

For more information, visit www.desatech.com

115603-01A

(V)3612ST specifications

Desa (V)3612ST is an advanced electronic device designed to enhance heating and ventilation systems in both residential and commercial settings. It combines state-of-the-art technology with user-friendly features, making it an ideal solution for those seeking efficiency and comfort in their environments.

One of the standout features of the Desa (V)3612ST is its variable speed motor, which allows for adjustable airflow. This technology enables users to customize their heating or cooling experiences based on personal preferences or external weather conditions. The variable speed capability also results in quieter operation, ensuring a more peaceful atmosphere.

The Desa (V)3612ST is equipped with a digital display that provides real-time information about temperature settings and system performance. This display is intuitive and user-friendly, allowing for easy adjustments to settings without the need for complex navigation. The inclusion of smart thermostatic controls further enhances functionality, enabling remote monitoring and control via mobile applications. This means that users can adjust their heating or cooling systems even when they are not at home, contributing to energy savings and convenience.

In terms of safety, the Desa (V)3612ST incorporates several features designed to protect users and property. An automatic shut-off function prevents overheating, while built-in sensors monitor air quality and system performance, alerting users to potential issues before they escalate. This adds an extra layer of reliability and peace of mind.

Energy efficiency is another key characteristic of the Desa (V)3612ST. It meets or exceeds the latest energy efficiency standards, helping users to lower their utility bills while minimizing their environmental impact. The device’s design promotes optimal airflow and heat distribution, ensuring that energy is used effectively.

In conclusion, the Desa (V)3612ST stands out for its innovative technology, user-friendly features, and commitment to safety and energy efficiency. Its variable speed motor, digital display, smart controls, and safety measures make it a versatile choice for anyone looking to improve their heating and ventilation systems. Whether used in homes or businesses, the Desa (V)3612ST delivers reliable performance and enhances overall comfort.