Vermont Casting ODSR36A Install Remainder of Chimney Sections, Installing Chimney In a Chase

Page 13

Cut and frame the hole. It is good practice to use fram- ing lumber that is the same size as the rafters. Install the frame securely because the chimney top and flash- ing anchored to the frame must be able to withstand heavy winds.

Install Remainder of Chimney Sections

Since you have already preplanned the height of your termination according to the Ten Foot Rule, continue to install pipe to the predetermined height.

Check the chimney top installation instructions for details on how high above the roof top the chimney sections (all pipes) should extend.

Majestic Fireplaces® ODSR Series "A"

Air Space Clearances

Combustible framing material MUST NOT penetrate AIR SPACE (shaded areas).

1¹⁄₂"

Standoff

¹⁄₂" air space to sides

Installing Top Housing or Termination

Follow the installation instructions provided with the chimney termination you have selected.

Installing Chimney In a Chase

Refer to Page 4, Figure 3 for an illustration of a typical chase installation.

CAUTION: Treatment of firestop spacers and con- struction of chase may vary with type of building. These instructions are not a substitute for local building codes. You must check your local building codes to determine specific requirements for your city or state. NOTE: Other building materials may be required in ad- dition to CFM Corporation Firestop Spacers.

Finishing

CAUTION: All joints between the finished wall and the fireplace surround (top/sides) must be sealed with non-combustible material to prevent cold air leakage into the room. Only noncombustible material may be applied to the facing of the fireplace surround. (Black painted area) (Fig. 19)

Front View

Wall

Shield

Only noncombustible material may be applied as facing to the black fireplace surround.

Side View

Firestop

¹⁄₂" Air Space to Back

¹⁄₂" Air Space to Sides

0" Clearance to Floor

Hearth

Extension

FP559

Finish Wall

Finish the wall with material of your choice. Do not install a combustible mantel shelf less than 12"

(305 mm) from the top of the fireplace opening. Do not install a mantel face plate less than 6" (159 mm) from top of fireplace opening. (Fig. 21) If a combus- tible material is used below a flat mantel shelf, consult your local building codes for minimum clearance from top of fireplace opening to bottom of mantel shelf.

All joints (top, bottom and sides) where wall or deco- rative facing material meets fireplace surround must be completely sealed with a noncombustible material. (Figs. 20 and 21)

Fig. 19 Minimum clearances to combustibles.

NOTE: No side wall protection is required for fireplaces installed at 45° to two (2) side walls (corner installation).

Often a decorative surround or vertical portion of the mantel is desired. If this is constructed of any combus- tible material it must be within the safe zone indicated in Figure 22.

20006811

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Odsr Series a Table of Contents Safety Information ODSR36A Series Woodburning Fireplace Chase Installation Chimney Requirements Offset Installations Mounting the Fireplace Planning InformationPlanning the Chimney Run Ten Foot RuleChase Installation InstallationChimney Supports Insulating Fireplace Enclosure For Cold ClimatesStraight-Up Chimney Installation Chimney SetupOffset Installation FramingCutting the Hole Positioning, Safety Strips Securing the FireplaceFraming the Ceiling Hole Angle of Chimney at CeilingInstalling the Chimney System Installing Outside Air KitProper Firestop Spacer Installation Installing the Firestop Spacer Ceiling HoleAdditional Ceilings Continue Installing Pipe to Complete RunPenetrating the Roof Locate Chimney Centerpoint On RoofInstalling Top Housing or Termination Install Remainder of Chimney SectionsInstalling Chimney In a Chase FinishingMantel clearances Side Wall Protection Hearth InstallationExamples of wall shield insulation Example for Common Brick Example of Determining Hearth Extension Equiva- lentsSide View Fireplace Top View Installing Line for Gas LogsItem/Model Number ODSR36A/42A Outdoor Woodburning FireplaceAccessory Description Model Number AccessoriesComponent Description Model Number Chimney ComponentsChimney Components Canada Majestic Fireplaces Odsr Series a Limited Warranty & 30 Year Protection Plan CFM Corporation

ODSR42A, ODSR36A specifications

Vermont Castings has long been renowned for producing high-quality, efficient, and aesthetically pleasing heating solutions. The ODSR36A and ODSR42A gas fireplaces represent the epitome of this legacy, combining advanced technology and design to enhance any living space.

One of the standout features of both models is their exceptional heating capabilities. The ODSR36A offers a maximum input of approximately 36,000 BTUs, while the ODSR42A boasts an impressive 42,000 BTUs. This ensures that they can effectively heat spaces of various sizes, making them suitable for both small and large rooms.

The design of these fireplaces is another notable characteristic. Both models come with a classic cast iron finish that provides a timeless aesthetic to any home. The large viewing area offered by the expansive glass doors invites warmth and ambiance into the room, allowing users to enjoy the beauty of the flames without the hassle of traditional wood-burning fireplaces.

Efficiency is paramount for modern consumers, and both the ODSR36A and ODSR42A excel in this department. With a remarkable thermal efficiency rating, these models ensure that more heat is produced from less fuel, translating into cost savings over time. Additionally, the convenience of gas operation eliminates the need for wood storage, ashes, and the cleanup associated with traditional fireplaces.

Safety and user-friendliness are also integrated into the design of the ODSR series. Both models are equipped with pilot ignition systems, simplifying the lighting process. Moreover, they come with advanced safety features such as a safety shut-off mechanism, which automatically activates in case of gas leaks, ensuring peace of mind for users.

The ODSR36A and ODSR42A also offer customizable options to suit different tastes and home styles. Choices include a variety of trims and decorative elements, allowing homeowners to create a fireplace that matches their décor.

With quiet operation, quick heat-up times, and minimal emissions, the Vermont Castings ODSR36A and ODSR42A stand out as top choices for those seeking the perfect combination of style, efficiency, and technological innovation in their home heating solutions. These fireplaces not only serve as functional heating units but also as beautiful focal points that enhance the comfort and charm of any living space.
Top Page Image Contents