Centro 5000AS Lighting the Second Burner, Lighting the Side Burner, Visually Check Burner Flame

Page 8

H I

LOW

W A R N I N G

If the heat output is too low, the flow control feature may have been activated by a gas leak. If so, turn off the burner valve and cylinder valve, and perform the “Leak Test”. If there aren’t any leaks, re-light the burner.

Lighting the Second Burner

•Turn the second control knob on the main control panel to the “HIGH” position. The unlit burner will automatically ignite.

Lighting the Side Burner

Use the push-button igniter on the main control panel and the right control knob on the side burner panel.

•Push in and turn the right control knob to the “HIGH” position.

•Push the igniter button until a loud click is heard, which is the

spark being formed. Repeat several times if the burner does not light.

•If the burner does not light after several tries, turn the right control knob off and wait 5 minutes for the gas to clear.

•Repeat the above instructions. If the side burner still does not light,

refer to the troubleshooting section for help or light the burner manually.

Note: The side burner is designed to accept a maximum weight of 20 lb. Do not overload the side burner.

Lighting the Side Burner with a Match

•Place match in front ring of provided match holder.

•Place a lighted match through the hole to within 16 cm (1/2˝ ) of the side burner.

•Push in and turn the burner knob to the “HIGH” position. At this point, the burner should light, if it doesn’t after 5 seconds, turn the control knob back to the “OFF” position and wait for the gas to clear.

•Wait 5 minutes, and then repeat the manual lighting procedure. If after three tries the burner still does not light, review the troubleshooting guide for help.

Shutting Down the Barbecue After Use

•Turn off the gas cylinder valve.

•Turn the burner control valve to the “OFF” position.

This sequence is important as it prevents residual gas from being left in the system under pressure and will make the next use easier.

Visually Check Burner Flame

Take off the grates and heat shield. Light burners. Adjust the flame by turning the knobs from “HIGH” to “LOW”. The flames will be smaller when the knobs are in the “LOW” position. Always check flame prior to each use. Perform flame check for side burner.

6

Page 7 Page 9
Image 8
Page 7 Page 9
Contents F E U S E , C a R E a N D a S S E M B L Y M a N U a L E a R L I M I T E D W a R R a N T Y0 7 0 1 8 5 1 2 7 7 4 P R O P a N E 0 7 0 2 8 5 1 2 8 3 8 N a T U R a L G a SB L E O F C O N T E N T S Installation D I T I O N a L R N I N G SL L I N G E C Y L I N D E R A N S P O R T a T I O N a N D S T O R a G E C Y L I N D E RTo Avoid Unnecessary Risks Perform a Leak Test S E a N D R E G U L a T O RA K T E S T I N G I O R T O U S I N G Following Must be CheckedG H T I N G E G R I L L Lighting the Second Burner Lighting the Side BurnerLighting the Side Burner with a Match Shutting Down the Barbecue After UseT I S S E R I E B U R N E R I G N I T E R L I G H T I N G P S O N U S I N G U R R O T I S S E R I EHow to Prevent Food From Sticking on the Cooking Grates P S O N U S I N G U R B a R B E C U EConnecting to Gas Line Disconnecting From Gas LineF O R M a T I O N O N T U R a L G a S M O D E L Natural Gas Supply ConnectionE a N I N G D M a I N T E N a N C E O R a G ETroubleshooting G U I D E Problem Possible Causes Corrective ActionR T S L I S T F O R 1 2 8 3 8 P R O P a N E1 2 7 7 4 P R O P a N E 1 2 1 0 2 N a T U R a L G a S 1 2 1 0 2 N a T U R a L G a S Hardware Pack List Tools Needed for AssemblyS E M B L Y I N S T R U C T I O N S Page Page For Propane Model only Page S T R I B U T O R
Top Page Image Contents