Char-Broil 80015625 Sideburner Ignitor Lighting, Sideburner Match Lighting, Burner Flame Check

Page 8

WARNING

Turn controls and gas source or tank OFF when not in use.

CAUTION

If ignition does NOT occur in 5 seconds, turn the burner controls OFF, wait 5 minutes and repeat the lighting procedure. If the burner does not ignite with the valve open, gas will continue to flow out of the burner and could accidently ignite with risk of injury.

Match-Lighting

sDo not lean over grill while lighting.

1.Open lid. Turn on gas at LP cylinder.

2.Place lit match into match holder (hanging from cart side panel), light burner on right or left side of grill.

3.Push in and turn far right or far left burner knob to HIGH. Be sure burner lights and stays lit.

4.Light adjacent burners in sequence by pushing knobs in and turning to HIGH.

Sideburner Ignitor Lighting

sDo not lean over grill while lighting.

1.Top cover must be open when burner is operational.

2.To ignite SIDEBURNER, open sideburner cover.

3.Turn sideburner knob to HIGH, push and hold ELECTRONIC IGNITOR button.

4.If sideburner does NOT light in 5 seconds, turn knob to OFF, wait 5 minutes, then repeat lighting procedure.

Sideburner Match Lighting

1.Open sideburner cover.

2.Place lit match near burner.

3.Turn sideburner knob to HIGH. Be sure burner lights and stays lit.

Burner Flame Check

Remove cooking grates and flame tamers. Light burners, rotate knobs from HIGH to LOW. You should see a smaller flame in LOW position than seen on HIGH. Perform burner flame check on sideburner, also. Always check flame prior to each use. If only low flame is seen refer to "Sudden drop or low flame" in the Troubleshooting Section.

HIGH

LOW

Turning Grill Off

Turn all knobs to OFF position. Turn LP cylinder off by turning hand-wheel clockwise to a full stop.

Ignitor Check

Turn gas off at LP cylinder. Press and hold electronic ignitor button. "Click" should be heard and spark seen each time between collector box or burner and electrode. See "Troubleshooting" if no click or spark.

Valve Check

Important: Make sure gas is off at LP cylinder before checking valves. Knobs lock in OFF position. To check valves, first push in knobs and release, knobs should spring back. If knobs do not spring back, replace valve assembly before using grill. Turn knobs to LOW position then turn back to OFF position. Valves should turn smoothly.

Hose Check

Before each use, check to see if hoses are cut or worn. Replace damaged hoses before using grill. Use only valve/hose/regulator specified by manufacturer.

General Grill Cleaning

Do not mistake brown or black accumulation of grease and smoke for paint. Apply a strong solution of detergent and water or use a grill cleaner with scrub brush on insides of grill lid and bottom. Rinse and allow to completely air dry. Do not apply a caustic grill/oven cleaner to painted surfaces.

Plastic parts: Wash with warm soapy water and wipe dry.

useDo not citrisol, abrasive cleaners, degreasers or a concentrated grill cleaner on plastic parts. Damage to and failure of parts can result.

Porcelain surfaces: Because of glass-like composition, most residue can be wiped away with baking soda/water solution or specially formulated cleaner. Use nonabrasive scouring powder for stubborn stains.

Painted surfaces: Wash with mild detergent or nonabrasive cleaner and warm soapy water. Wipe dry with a soft nonabrasive cloth.

Stainless steel surfaces: To maintain your grill’s high quality appearance, wash with mild detergent and warm soapy water and wipe dry with a soft cloth after each use. Baked-on grease deposits may require the use of an abrasive plastic cleaning pad. Use only in direction of brushed finish to avoid damage. Do not use abrasive pad on areas with graphics.

Cooking surfaces: If a bristle brush is used to clean any of the grill cooking surfaces, ensure no loose bristles remain on cooking surfaces prior to grilling. It is not recommended to clean cooking surfaces while grill is hot.

8 • 463360408

Image 8
Contents Model 463360408 Product Guide Call Grill Service Center for Help and Parts Installation Safety PrecautionsSafety Symbols For residential use only. Do not use for commercialTable of Contents LP Liquefied Petroleum Gas LP Cylinder FillingUL listed Overfill Protection Only LP cylinders equipped with this type of valveConnecting Regulator to the LP Cylinder For your safetyUseDo not household cleaning agents. Damage to gas LP Cylinder ExchangeTurn all grill control knobs to OFF Leak Testing Valves, Hose and RegulatorConnection, do not use this regulator For Safe Use of Your Grill and to Avoid Serious Injury Ignitor LightingBurner Flame Check Sideburner Ignitor LightingSideburner Match Lighting Cleaning the Burner Assembly Storing Your GrillTurn gas off at control knobs and LP cylinder Very Important Burner tubes must re-engage valveFood Safety How To Tell If Meat Is Grilled ThoroughlyIndirect Cooking Indirect Cooking InstructionsRoutine Care Stubborn Stains and RustDescription KeyDescription Key Parts Diagram Model No Assembly Model No 20x1-1/2 screws and 1/4-20 flange nuts Front Panel Qty #8x3/8 Self-Tap Screw 463320107 20x1/2 Back of cart Qty #8x3/8 Screw Heat Failure to install grease cup clip and cup Troubleshooting Emergencies Possible Cause Prevention/SolutionElectronic Ignition Troubleshooting Electronic Ignition SectionLimited Warranty Please register your product online at Grilling Safety Checklist Thank You for Your Purchase