Char-Broil 463460708 manual Troubleshooting Electronic Ignition, Section

Page 25

Troubleshooting - Electronic Ignition

Problem (Ignition)

Possible Cause

Check Procedure

Prevention/Solution

 

 

 

 

SECTION I

• Battery not installed

• Check battery orientation.

• Install battery (make sure that “+” and “–”

No sparks appear at

any electrodes when

properly.

 

connectors are oriented correctly, with “+” end up

ignition button is

 

 

and “–” end down.)

pushed; no noise can

• Dead battery.

• Has battery been used

• Replace battery with new AA-size alkaline battery.

be heard from spark

module.

 

previously?

 

 

• Button assembly not

• Check to insure threads are

• Unscrew button cap assembly and reinstall, making

 

installed properly.

properly engaged. Button

sure threads are aligned and engaged fully.

 

 

should travel up and down

 

 

 

without binding.

 

 

• Faulty spark module.

• If no sparks are generated

• Replace spark module assembly.

 

 

with new battery and good

 

 

 

wire connections, module is

 

 

 

faulty.

 

 

 

 

 

SECTION II

• Output lead

• Are output connections on

• Remove and reconnect all output connections at

No sparks appear at

any electrodes when

connections not

and tight?

module and electrodes.

ignition switch is

connected.

 

 

pushed; noise can be

 

 

 

heard from spark

 

 

 

module.

 

 

 

 

 

 

 

SECTION III

• Output lead

• Are output connections on

• Remove and reconnect all output connections at

Sparks are present

but not at all

connections not

and tight?

module and electrodes.

electrodes and/or not

connected.

 

 

at full strength

• Arcing to grill away

• If possible, observe grill in

• If sparks are observed other than from burner(s),

 

 

from burner(s).

dark location. Operate

wire insulation may be damaged. Replace wires.

 

 

ignition system and look for

 

 

 

arcing between output wires

 

 

 

and grill frame.

 

 

• Weak battery.

• All sparks present but weak

• Replace battery with a new AA-size alkaline battery.

 

 

or at slow rate.

 

 

• Electrodes are wet.

• Has moisture accumulated

• Use paper towel to remove moisture.

 

 

on electrode and/or in burner

 

 

 

ports?

 

 

• Electrodes cracked or

• Inspect electrodes for

• Replace cracked or broken electrodes.

 

broken “sparks at

cracks.

 

 

crack”.

 

 

 

 

 

 

463460708 • 25

Image 25
Contents Model 463460708 Product Guide Installation Safety Precautions Call Grill Service Center for Help and PartsSafety Symbols For residential use only. Do not use for commercialTable of Contents LP Cylinder Filling LP Liquefied Petroleum GasOnly LP tanks equipped with this type of valve For your safety Connecting Regulator to the LP CylinderUseDo not household cleaning agents. Damage to gas LP Cylinder ExchangeConnection, do not use this regulator Leak Testing Valves, Hose and RegulatorTurn all grill control knobs to OFF Main Burner Ignitor Lighting For Safe Use of Your Grill and to Avoid Serious InjurySDo not lean over grill while lighting Open lid during lightingSideburner Ignitor Lighting General Grill CleaningSideburner Match Lighting Burner Flame CheckStoring Your Grill Cleaning the Burner AssemblyTurn gas off at control knobs and LP cylinder Very Important Burner tubes must reengage valveHow To Tell If Meat Is Grilled Thoroughly Food SafetyIndirect Cooking Indirect Cooking InstructionsStubborn Stains and Rust Routine CareDescription Key KeyDescription Parts Diagram Model No Rear #8-32 Flange Nut #8-32x3/8 Screw Flange nuts Sharp EDGES! Wear gloves if necessary Sideburner valve bracket Control knob bezel Burner tube Place cooking grates into grill bottom Grease Cup Wire AA Battery Emergencies Possible Cause Prevention/Solution TroubleshootingElectronic Ignition Section Troubleshooting Electronic IgnitionLimited Warranty Please register your product online at Thank You for Your Purchase Grilling Safety Checklist