Preparation Before Cooking

·Wash the porcelain coated Cooking Grids (1) with a mixture of hot water and baking soda.

·Empty the foil pan and grease tray after each cooking session so excessive grease does not accumulate.

Failure to remove grease may result in grease dripping onto the cart and/or a grease fire in the tray.

Lighting the Grill Using the Integra-

Spark Ignition System

·Open Hood before lighting the grill to prevent an explosion from gas buildup.

·Always inspect the gas hose and regulator assembly

before each use. If the hose is cut, damaged, or shows signs of excessive abrasion or wear, do not use the LP gas grill. Contact the manufacturer, as the hose and regulator assembly must be replaced with an assembly specified by the manu facturer prior to further use of the LP gas grill.

How to light your LP gas grill (See diagram below for illustrations)

1)Open Hood.

2)Important: Make sure control knobs are turned “off” first. Open the LP gas cylinder valve by turning the valve handle counter-clockwise until it stops.

2.Turn LP cylinder handle counter-clockwise - “ON”

3)From the “Off” position, push control knob in on the left burner and turn counter-clockwise until you feel resistance. Pause 4 seconds, then continue turning the control knob until a click is heard and the burner is lit.

4)Light the remaining burners by turning the control knob counter-clockwise. Your grill has a crossover ignition system that allows the burners to light successively off one another.

Confirm each burner is lit before lighting another burner.

5)If any of the burners do not light, repeat Step 3. The burner should light within three or four attempts. If burner still does not light, try the next burners from left to right.

WARNING: If any or all burners fail to light after following Steps 3 & 4, turn all knobs to the “off” position and close the valve on the LP gas cylinder. Wait five minutes; then repeat all of the above lighting procedures.

Note:If the burners still fail to light, refer to the Troubleshooting page. The burner can be lit manually. See Manual Lighting of the Grill.

6)After ignition, preheat the grill by turning the control to “High” position for 3-5 minutes. The grill should be pre-heated before every cooking session.

The hood should be closed during preheating.

WARNING: If a burner goes out during the cooking cycle, turn all knobs to the off position and close the valve on the LP cylinder. Open hood and wait five minutes before attempting to relight the grill.

1. Open hood

3.Push in and turn control knob counter-clockwise until you feel resistance, wait 4 seconds then continue until a click is heard and the burner is lit.

8362, 8462 specifications

Aussie 8462,8362 are two advanced models that showcase the innovation in modern technology, particularly in the field of telecommunications and data transmission. These models are a testament to Australia’s growing influence in the tech sector, particularly in developing solutions that cater to both local and international markets.

One of the main features of the Aussie 8462 is its exceptional data processing capacity. This model is engineered to handle large volumes of data with remarkable efficiency, making it ideal for businesses that rely on real-time analytics. Additionally, the 8462 incorporates advanced encryption technologies, ensuring that data remains secure during transmission. This feature is increasingly important in an era where data breaches are rampant, and businesses must prioritize customer privacy.

On the other hand, the Aussie 8362 focuses more on connectivity and versatility. It has been designed to support multiple connectivity options, including 5G, LTE, and Wi-Fi 6. This variety allows it to cater to a wide range of devices, ensuring seamless communication in diverse environments. Moreover, the 8362 is equipped with smart routing capabilities that optimize network traffic, thereby enhancing overall performance and reducing latency.

Both models employ state-of-the-art artificial intelligence algorithms to facilitate predictive analysis and automate network management tasks. This functionality significantly reduces the need for manual intervention, allowing IT departments to focus on strategic initiatives rather than routine maintenance.

In terms of physical characteristics, both the 8462 and 8362 boast rugged and compact designs, suitable for various installation environments. They are built with durable materials that can withstand extreme weather conditions, making them ideal for outdoor deployments. Furthermore, their energy-efficient architecture ensures that they consume less power while delivering high performance, contributing to sustainability efforts.

In conclusion, the Aussie 8462 and 8362 represent a significant advancement in telecommunications technology. Their integration of robust security features, advanced connectivity options, and intelligent network management systems makes them suitable for modern businesses looking to thrive in a digital-first world. As Australia continues to innovate in this space, these models set a benchmark for future developments in telecommunications technology.