Adjusting Main Burner Electrodes
1.Remove four (4) grill plates.
2.Remove ceramic plaques.
3.Remove plaque rack.
4.Remove five (5) burner hoods from five (5) main burners.
5.Remove five (5) collector boxes from five (5) main burner electrodes, one (1) 10 - 16 x 1/2" Phillips stainless steel screw for each collector box.
6.At this time, check for proper sparking of the electrodes. Turn electrode knob, the spark should occur between the second and third port hole on main burner.
To adjust spark angle you will use two (2) needle nose pliers. Grasping electrode wire 1/2" back from tip of electrode with first pair of needle nose pliers adjust tip of electrode with second pair of needle nose pliers.
7.Check ignition of main burners. Make additional adjustments to electrodes if required.
8.Locate main burner with electrode that is to the left of chip tray. Place collector box over electrode. Place flange on collector box beneath flange on chip tray guide. The clearance hole in collector box will align with clearance hole in chip tray guide. Insert and attach one (1)
9.Place four (4) additional collector boxes over four (4) additional main burners with electrodes.
10.Attach four (4) collector boxes to bottom of inner liner with four
(4)
11.Replace five (5) burner hoods over five (5) main burners.
12.Replace plaque rack.
13.Replace ceramic plaques onto plaque rack.
14.Replace four (4) grill plates.
15.Adjustment of main burner electrodes is completed.
TROUBLE-SHOOTING
If your Superb gas grill does not function properly, use the following checklist before contacting your dealer for service.
You may save the cost of a service call.
1.Grill won't light when the rotary ignitor is turned.
a.With the gas tuned off, remove the grill plates, ceramic plaques and plaque rack. Turn the ignitor knob clockwise to check the spark. You should see a spark jump from tip of the ignitor. If there is a spark, check the gas supply. Is the tank full? Is the line purged of air? Can you light the burner with a match?
b.Check air shutter adjustment, close as needed.
c.Do other burners light?
d.Check the orifice for blockage.
e.Is the ignitor tip clean and free from debris?
f.Clean ignitor tip.
2.Burner flame is yellow or orange and there is a smell of gas.
a.Check the burner inlet for obstructions.
b.Check the air shutter for proper adjustment.
c.Check for spiders, spider webs and debris.
3.Low heat with control knob set on "HI."
a.Is the fuel hose bent or kinked?
b.Is there an adequate gas supply?
c.If there is only one burner that appears low, does the orifice or burner need cleaning?
d.Is the air shutter too far open or closed?
e.Is the gas supply, or gas pressure low?
f.Has the grill been preheated for at least 10 minutes?
4.The smell of gas with flames appearing yellow or the gas grill does not reach temperature and heats unevenly.
a.Check for spiders or insects.
b.Spiders and insects can nest in the burner of this or any grill, and cause a disruption in the flow of gas from the burner. This is dangerous and can cause a fire behind the valve cover, damaging the grill and making it unsafe to operate.
You should inspect the burners periodically or immedi- ately if any of these conditions occur or persist.
5.The burners make popping noises.
a.Check air shutter adjustment.
b.Check burners for clogged ports.
HOW TO ORDER REPAIR PARTS...
All parts listed in the Parts List have a part No. When ordering parts, first obtain the Model No. from the nameplate on your equipment. Then determine
the Part No. (not the Index No.) and the Description of each part from the appropriate illustration and list. Be sure to give all this information...
Grill Model Number |
| Part Description |
|
| ||
|
|
| ||||
Grill Serial Number |
|
| Type of Gas (Propane or Natural) |
| ||
|
|
| ||||
Part Number |
|
|
|
|
| |
|
|
|
|
| ||
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store. Order parts through your local dealer.
Shipments contingent upon strikes, fires, and all causes beyond our control.
Page 12 | Empire Comfort Systems, Inc. Nine Eighteen Freeburg Ave. Belleville, Illinois |