Rotisserie Troubleshooting, Problem Check Cure

30	ROTISSERIE TROUBLESHOOTING

PROBLEM	CHECK	CURE

Rotisserie burner does not light.	Did you hold the burner control knob in and	Try to relight burner by holding burner control knob in and continue holding in until
	hold in for 20 seconds until after burner	20 seconds after burner has ignited.
	ignited?

	Did you wait to see the entire ceramic surface	When relighting burner by holding burner control knob in, wait to see the entire
	become alight before counting 20 seconds?	ceramic surface become alight before counting 20 seconds?

	Did you repeatedly use the snap ignition until	After waiting ﬁ ve minutes for gas to clear, try repeatedly using the snap igniter until
	the burner ignited?	the burner ignites (refer to “Lighting the Rotisserie Burner”).

	Does the igniter work (Do you see a spark	Try manually lighting the burner (refer to “Lighting the Rotisserie Burner”). Call
	when you repeatedly use the snap igniter?	customer service.

General Symptoms:	The excess ﬂ ow safety device, which is part of	To reset the excess ﬂ ow safety device turn all burner control knobs and the cylinder
Burner does not light. -or- Burner has	the barbecue to cylinder connection, may have	valve to “OFF”. Disconnect the regulator from the cylinder. Turn burner control
a small ﬂickering ﬂame	activated.	knobs to “START/HI”. Wait at least 1 minute. Turn burner control knobs to “OFF”.
		Reconnect the regulator to the cylinder. Turn cylinder valve on slowly. Refer to
		“Lighting Instructions”.

If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web site. Log onto www.weber.com®.

OPERATING THE HANDLE LIGHT

The Weber Grill Out™ Handle Light has a built-in “Tilt Sensor.” With the power button (a) activated, the light will come on when the grill lid is open. The light will turn off when the lid is closed. For daytime use, deactivate the sensor by pressing power button (a).

HANDLE LIGHT TROUBLESHOOTING

PROBLEM	CHECK	CURE

Weber Grill Out™ Handle	Are the batteries old?	Replace batteries.
Light does not light.
Light does not light.	Are the batteries installed correctly?	See assembly illustration.
	Are the batteries installed correctly?	See assembly illustration.

	Is the lid in the up position with the power button ON?	Light will activate when lid is open.

	Is the Weber Grill Out™ Handle Light activated?	Press the power button.
	Is the Weber Grill Out™ Handle Light positioned correctly on the handle?	Adjust position (See assembly illustration).

If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web site. Log onto www.weber.com®.

SIDEBURNER TROUBLESHOOTING

PROBLEM	CHECK	CURE

Side Burner does not light.	Is gas supply off?	Turn supply on.
	The excess ﬂ ow safety device, which is part	To reset the excess ﬂ ow safety device turn all burner control knobs and the cylinder
	of the barbecue to cylinder connection, may	valve off. Disconnect the regulator from the cylinder. Turn burner control knobs to
	have activated.	START/HI. Wait at least 1 minute. Turn burner control knobs to “OFF”. Reconnect
		the regulator to the cylinder. Turn cylinder valve on slowly. Refer to “Lighting Instruc-
		tions”.

Flame is low in “HI” position.	Is the fuel hose bent or kinked?	Straighten hose.

Push button ignition does not work.	Does burner light with a match?	If match lights burner, check igniter (see Sideburner Maintenance).

If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web site. Log onto www.weber.com®.