Weber 43143 Handle Light Troubleshooting, Problem Check Cure, Operating the Handle Light

	TROUBLESHOOTING	21
PROBLEM	CHECK	CURE
Burners burn with a yellow or orange flame, in	Inspect Spider/Insect Screens for possible obstructions.	Clean Spider/Insect Screens. (See Section “Annual
conjunction with the smell of gas (This is normal	(Blockage of holes.)	Maintenance”)
for the burner lighting tube).
Symptoms:	The excess flow safety device, which is part of the	To reset the excess flow safety device turn all burner control
Burners do not light. -or- Burners have a small	barbecue to cylinder connection, may have activated.	knobs and the cylinder valve off. Disconnect the regulator
flickering flame in the “HI” position. -or-		from the cylinder. Turn burner control knobs to “HI”. Wait at
Barbecue temperature only reaches 250˚ to 300˚		least 1 minute. Turn burner control knobs to “OFF”. Reconnect
in the “HI” position.		the regulator to the cylinder. Turn cylinder valve on slowly.
		Refer to “Lighting Instructions”.
Burner does not light, or flame is low in “HI”	Is LP fuel low or empty?	Refill LP cylinder.
position.
	Is fuel hose bent or kinked?	Straighten fuel hose.
	Does Burner light with a match?	If you can light Burner with a match, then check the
		Crossover® ignition system.
	Did you use the snap igniter several times until the main	Make sure to hold the control knob in for two seconds after
	burner lit (See Lighting Instructions)?	snapping the igniter and seeing the orange flame from the
		burner lighting tube.
	Does the igniter work? (Do you see a spark when you	Try manually lighting the burner (refer to “Main Burner
	repeatedly use the snap igniter?)	Manual Lighting”). Call customer service.
Experiencing flare-ups:	Are you preheating barbecue in the prescribed manner?	All burners on HI for 10 to 15 minutes for preheating.
	Are the cooking grates and Flavorizer® bars heavily	Clean thoroughly. (See Section “Cleaning”)
	coated with burned-on grease?
CAUTION: Do not line the bottom tray	Is the bottom tray “dirty” and not allowing grease to flow	Clean bottom tray.
	into catch pan?
with aluminum foil.
Burner flame pattern is erratic. Flame is low when	Are burners clean?	Clean burners. (See Section “Maintenance”.)
burner is on “HI”. Flames do not run the whole
length of the burner tube.
Inside of lid appears to be “peeling.” (Resembles	The lid is porcelain enamel or stainless steel, not paint.	Clean thoroughly. (See Section “Cleaning”.)
paint peeling.)	It cannot “peel”. What you are seeing is baked on grease
	that has turned to carbon and is flaking off.
	THIS IS NOT A DEFECT.

If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web site. Log onto www.weber.com®.

OPERATING THE HANDLE LIGHT

The Weber Grill Out™ Handle Light has a built-in “Tilt Sensor.” With the power button (a) activated, the light will come on when the grill lid is open. The light will turn off when the lid is closed. For daytime use, deactivate the sensor by pressing power button (a).

HANDLE LIGHT TROUBLESHOOTING

PROBLEM	CHECK	CURE
Weber Grill Out™ Handle	Are the batteries old?	Replace batteries.
Light does not light.
	Are the batteries installed correctly?	See assembly illustration.
	Is the lid in the up position with the power button ON?	Light will activate when lid is open.
	Is the Weber Grill Out™ Handle Light activated?	Press the power button.
	Is the Weber Grill Out™ Handle Light positioned correctly on the handle?	Adjust position (See assembly illustration).

If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web site. Log onto www.weber.com®.

WWW.WEBER.COM®