Brinkmann 2610 Series owner manual Lighting Instructions, Lighting the Main Burners

Page 10

WARNING

LIGHTING INSTRUCTIONS:

Follow the instructions exactly.

1.OPEN THE GRILL LID before attempting to light a burner so that fumes do not accumulate inside the grill. An explosion could occur if grill lid is down.

2.Check that all burner control knobs and the cylinder valve are turned to the OFF position.

3.Turn on the fuel supply by rotating the cylinder valve knob counterclockwise to full open.

4.DO NOT stand with head, body, or arms over the grill when lighting.

LIGHTING THE MAIN BURNERS:

1.Open lid before lighting burner.

2.Make sure all control knobs are in the OFF position.

3.Select the burner to be lit. Push and turn the control knob of that burner to the HIGH position.

4.Press the electronic igniter and hold for 3-5 seconds until burner ignites.

5.If burner does NOT ignite immediately, turn the burner control knob to OFF, wait 5 minutes for gas to evacuate the grill. Repeat steps 1 through 5 until burner ignites.

6.If burner does not ignite using the push button igniter wait 5 minutes, see "Match Lighting the Main Burners" section.

OFF

HIGH

LOW

GRILL LIGHTING INSTRUCTIONS:

1.Read and follow all warnings and instructions in owner’s manual before lighting.

2.Open lid before lighting burner.

3.Make sure all control knobs are in the OFF position.

4.Select the burner to be lit. Push and turn the control knob of that burner to HIGH.

OFF

HIGH

LOW

5.Press the electronic igniter and hold for 3-5 seconds to light burner.

6.If burner does NOT ignite immediately, turn control knob to OFF, wait 5 minutes to allow gas to dissipate and repeat lighting procedure.

 

OFF

HIGH

 

FOR OUTDOOR USE ONLY

LOW

7.Repeat Steps 4-6 for lighting each burner. Always use electronic igniter for lighting each burner.

8.Refer to owner’s manual for match lighting procedure.

9.For assistance, call 1-800-527-0717.

10. To turn off, turn control knobs clockwise until it locks in OFF position.

OFF

HIGH

LOW

SIDE B LIGHT INSTR

1.Fol 1-3

LIG INS

2.Pus

SID con

HIG

3.Fol 5-1

LIG INS

7.Once lit, light adjacent burners in sequence by pressing in and rotating the control knob to the HIGH position.

MATCH LIGHTING THE MAIN BURNERS:

1.Open lid before lighting.

2.Turn the burner control knobs to OFF.

3.Place a paper match in the end of the matchlighter. Strike the match and place through lighting hole in the right hand side of the grill to approximately 1/2" (2 to 3 cm) from the burner.

4.Turn on the FAR RIGHT burner control knob to the HIGH position. The burner should light within

5 seconds.

Lighting Hole

Matchlighter

5.If the burner does not light, turn the control knob to OFF and wait 5 minutes for gas to evacuate the grill. Repeat steps 1 through 5 until the burner ignites.

6.Once lit, light adjacent burners in sequence by pressing in and rotating the control knob to the HIGH position.

7.If the burner does not light within the first few attempts of match lighting, there is a problem with the gas supply. Turn off the gas at the burner and cylinder. DO NOT attempt to operate the grill until the problem is found and corrected. See “Trouble Shooting” section of this manual.

9

Image 10
Contents Gas Stainless Steel Outdoor Grill Important Safety For Your SafetyPage Installation Information Cylinder SpecificationsPage Filling the LP GAS Cylinder Installing the LP GAS Cylinder Onto the GrillHose and Regulator Connecting Hose and Regulator to AN LP GAS Cylinder When to Perform a Leak Test Leak TestingChecking for Leaks PRE-START Check List Lighting the Main Burners Lighting InstructionsMatch Lighting the Main Burners Match Lighting the Side Burner Lighting the Side BurnerTurning OFF the Grill Preheating the Grill Operating the GrillBreaking in Your Grill Controlling FLARE-UPSRotisserie Cooking Side BurnerTransporting and Storage Before Storing Your GrillHardware Cleaning and MaintenanceBurner ASSEMBLY/MAINTENANCE CastingsTrouble Shooting Problem Possible Causes Burner will not lightGrilling to Proper Temperature CleanlinessHelpful Hints Assembly Instructions For Missing PARTS, Please Call Customer Service AT Parts Card Contents Step Attach back cart panel by using six M6 X 60mm bolts Tank Tray Assembly Step Spring Pin Grease Tray Bracket Igniter Button Cap Step Side Table Screw Holes Tool Drawer Step Pro Series 2610 Assembled Accessories Gallon PAN & Basket SET Warranty