Brinkmann Series 2210 owner manual Filling the LP GAS Cylinder, Hose and Regulator

Page 7

WARNING

FILLING THE LP GAS CYLINDER:

•Allow only qualified LP gas dealers to properly fill or repair your LP gas cylinder.

•New tanks should be purged prior to filling; inform LP gas dealer if you are using a new tank.

•DO NOT allow the cylinder to be filled beyond 80% capacity. Over-filled tanks can create a dangerous condition. Over-filled tanks can build-up pressure and cause the relief valve to expel propane gas vapors. The vapor is combustible and if it comes in contact with a spark source or flame an explosion causing severe burns, bodily harm, or death could occur.

•Always use a protective cylinder cap when grill is not connected to cylinder.

•If you exchange a cylinder with a qualified exchange program, be sure the cylinder has a Type 1 valve and an over-filling prevention device (OPD).

INSTALLING THE LP GAS CYLINDER ONTO THE GRILL:

 

1.

Check that the cylinder valve is closed by turning the knob

 

 

clockwise.

 

2.

Place the cylinder into the tank holder in the bottom

 

 

of cabinet.

 

3.

Orient the cylinder such that the valve opening faces the

 

 

side burner, and so that the hose is not kinked or damaged.

 

4.

Fully tighten the cylinder clamp underneath tank holder to

 

 

secure tank.

Tank Holder

 

 

5.

Attach or detach regulator to the LP gas cylinder only

 

 

when cylinder is at rest in tank holder.

 

HOSE AND REGULATOR:

 

Your grill is equipped with a Type 1 connection device with

 

the following features:

 

1.

The system will not allow gas flow from the cylinder until

 

 

a positive connection to the valve has been made.

 

 

NOTE: The cylinder valve must be turned off before any

 

 

connection is made or removed.

Cylinder Clamp

2.A thermal device that will shut off the gas flow if the device is subject to temperatures above 240°F to 300°F (115°C to 150°C). If this should happen, remove the entire regulator assembly and dispose of properly. A replacement regulator assembly can be purchased by contacting customer service

at 800-527-0717. The cause of the excessive heat should be determined and corrected before using your grill again.

3. A regulator flow limiting device, when activated, restricts the flow of gas to 10 cubic feet per hour. If the flow limiting device is activated, perform Regulator Resetting Procedure.

REGULATOR RESETTING PROCEDURE

1.Turn burner control knobs to "OFF”, turn off the cylinder valve and disconnect regulator from LP gas tank. Wait approximately two minutes.

2.Reattach regulator and slowly turn cylinder valve back on. The flow limiting device will now be reset.

6

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Heavy-Duty Gas Grill Important Safety Table of Contents General Warnings LP GAS Cylinder not Supplied with this Grill Installation InformationCylinder Specifications Filling the LP GAS Cylinder Regulator Resetting ProcedureHose and Regulator Connecting Hose and Regulator Connecting Hose and Regulator to AN LP GAS CylinderWhen to Perform a Leak Test Leak TestingChecking for Leaks PRE-START Check List Lighting the Main Burners Lighting InstructionsMatch Lighting the Main Burners Match Lighting the Side Burner Lighting the Side BurnerTurning OFF the Grill Controlling FLARE-UPS Operating the GrillBreaking in Your Grill Preheating the GrillSide Burner Rotisserie CookingGrilling to Proper Temperature CleanlinessHelpful Hints Burner ASSEMBLY/MAINTENANCE Cleaning and MaintenanceBefore Storing Your Grill Cooking GrillsHeat Distribution Plates Transporting and StorageTrouble Shooting Frequently Asked Questions Frequently Asked Questions Parts BAG Contents Assembly Instructions For Missing PARTS, Please Call Customer Service AT Step Tank Heat Shield Plate Place grease cup in middle of hole in heat shield plate Grill Body Assembly Step Place side burner grate on side burner Side Burner Igniter ProSeries 2210 Assembled Warranty

Series 2210 specifications

The Brinkmann Series 2210 is a sophisticated, high-performance scientific instrument designed for various analytical applications in laboratories. Renowned for its precision and reliability, the Series 2210 is engineered to meet the demands of modern research and quality control processes.

One of the standout features of the Brinkmann Series 2210 is its advanced measurement capabilities. Equipped with innovative sensors and cutting-edge technology, the device offers precise measurements across a wide range of parameters. Whether it is pH, conductivity, or ion concentration, the Series 2210 delivers accurate results, which are critical for laboratory analysis.

The user-friendly interface greatly enhances the overall experience. The device features an intuitive display that allows users to navigate through various functions and settings with ease. This ensures that even those with minimal technical expertise can operate the instrument effectively, making it accessible for a wide range of users.

Incorporating robust data management features, the Brinkmann Series 2210 allows for seamless data logging and storage. It can be connected to computers or laboratory management systems via USB or other connectivity options, facilitating easy data transfer and analysis. This feature is particularly beneficial for laboratories that require consistent record-keeping for compliance and reporting purposes.

Another key characteristic of the Series 2210 is its durability and build quality. Constructed with high-grade materials, it is designed to withstand the rigors of daily laboratory use while maintaining accuracy and reliability over time. This ruggedness ensures that it is a worthwhile investment for any laboratory looking to enhance its analytical capabilities.

The Brinkmann Series 2210 also embraces modern technological advancements by offering optional wireless connectivity. This feature enables remote monitoring and control, allowing users to access live data from mobile devices or computers. Such flexibility is vital for laboratories that prioritize efficiency and real-time analysis.

In summary, the Brinkmann Series 2210 stands out in the crowded field of analytical instruments due to its precision, user-friendly interface, robust data management capabilities, and durable construction. Whether for routine quality checks or advanced research applications, the Series 2210 continues to set a benchmark for reliability and performance in laboratory environments. Its commitment to innovation and excellence makes it a trusted choice for scientists and researchers worldwide.
Top Page Image Contents