Brinkmann Series 2210 owner manual PRE-START Check List

Page 10

6.Check each place listed (A–K) for growing bubbles which indicates a leak.

7.Turn off gas supply at cylinder valve.

8.Turn on control knobs to release gas pressure in hose.

9.Turn control knobs to "OFF" position.

10.Tighten any leaking connections.

11.Repeat soapy water test until no leaks are detected.

12.Turn off gas supply at cylinder valve until you are ready to use your grill.

13.Wash off soapy residue with cold water and towel dry.

14.Wait 5 minutes to allow all gas to evacuate the area before lighting grill.

CAUTION! DO NOT use the grill if leaks cannot be stopped. Contact a qualified gas appliance repair service.

NOTE: The leak test must be performed in an area that has adequate lighting in order to see if bubbles are developing. DO NOT use a flashlight to check for bubbles.

WARNING

PRE-START CHECK LIST:

Property damage, bodily harm, severe burns, and death could result from failure to follow these safety steps. These steps should be performed after the grill has been assembled and prior to each use. DO NOT operate this grill until you have read and understand ALL of the warnings and instructions in this manual.

PRE-START CHECK LIST:

Ensure that the grill is properly assembled.

Inspect the gas supply hose for burns, chaffing, kinks, and proper routing before each use. If it is evident there is excessive abrasion or wear, or the hose is cut, it must be replaced prior the grill being used. Replace with hose and regulator, Model No. 155-2400-0, which can be obtained by contacting customer service at 800-527-0717.

Leak check all gas connections and hose. See section on "Leak Testing".

Ensure that all electrical supply cords are properly grounded. Keep any electrical supply cord and the fuel supply hose away from any heated surfaces. Hose should be at least 3 inches from hot surfaces.

Position your grill on level ground in a well ventilated location, a safe distance from combustible materials, buildings and overhangs.

Properly place the empty grease tray under the grease drain hole in the bottom of the grill to catch grease during use.

DO NOT obstruct the flow of combustion and ventilation air.

9

Image 10
Contents Heavy-Duty Gas Grill Important Safety Table of Contents General Warnings Installation Information LP GAS Cylinder not Supplied with this GrillCylinder Specifications Filling the LP GAS Cylinder Regulator Resetting ProcedureHose and Regulator Connecting Hose and Regulator to AN LP GAS Cylinder Connecting Hose and RegulatorWhen to Perform a Leak Test Leak TestingChecking for Leaks PRE-START Check List Lighting the Main Burners Lighting InstructionsMatch Lighting the Main Burners Match Lighting the Side Burner Lighting the Side BurnerTurning OFF the Grill Preheating the Grill Operating the GrillBreaking in Your Grill Controlling FLARE-UPSRotisserie Cooking Side BurnerGrilling to Proper Temperature CleanlinessHelpful Hints Cleaning and Maintenance Burner ASSEMBLY/MAINTENANCETransporting and Storage Cooking GrillsHeat Distribution Plates Before Storing Your GrillTrouble Shooting Frequently Asked Questions Frequently Asked Questions Parts BAG Contents Assembly Instructions For Missing PARTS, Please Call Customer Service AT Step Tank Heat Shield Plate Place grease cup in middle of hole in heat shield plate Grill Body Assembly Step Place side burner grate on side burner Side Burner Igniter ProSeries 2210 Assembled Warranty

Series 2210 specifications

The Brinkmann Series 2210 is a sophisticated, high-performance scientific instrument designed for various analytical applications in laboratories. Renowned for its precision and reliability, the Series 2210 is engineered to meet the demands of modern research and quality control processes.

One of the standout features of the Brinkmann Series 2210 is its advanced measurement capabilities. Equipped with innovative sensors and cutting-edge technology, the device offers precise measurements across a wide range of parameters. Whether it is pH, conductivity, or ion concentration, the Series 2210 delivers accurate results, which are critical for laboratory analysis.

The user-friendly interface greatly enhances the overall experience. The device features an intuitive display that allows users to navigate through various functions and settings with ease. This ensures that even those with minimal technical expertise can operate the instrument effectively, making it accessible for a wide range of users.

Incorporating robust data management features, the Brinkmann Series 2210 allows for seamless data logging and storage. It can be connected to computers or laboratory management systems via USB or other connectivity options, facilitating easy data transfer and analysis. This feature is particularly beneficial for laboratories that require consistent record-keeping for compliance and reporting purposes.

Another key characteristic of the Series 2210 is its durability and build quality. Constructed with high-grade materials, it is designed to withstand the rigors of daily laboratory use while maintaining accuracy and reliability over time. This ruggedness ensures that it is a worthwhile investment for any laboratory looking to enhance its analytical capabilities.

The Brinkmann Series 2210 also embraces modern technological advancements by offering optional wireless connectivity. This feature enables remote monitoring and control, allowing users to access live data from mobile devices or computers. Such flexibility is vital for laboratories that prioritize efficiency and real-time analysis.

In summary, the Brinkmann Series 2210 stands out in the crowded field of analytical instruments due to its precision, user-friendly interface, robust data management capabilities, and durable construction. Whether for routine quality checks or advanced research applications, the Series 2210 continues to set a benchmark for reliability and performance in laboratory environments. Its commitment to innovation and excellence makes it a trusted choice for scientists and researchers worldwide.