Pride Mobility SC140 Axle Bearings and the MOTOR/TRANSAXLE Assembly, To Replace the Motor Brushes

Page 30

X I I . C A R E A N D M A I N T E N A N C E

AXLE BEARINGS AND THE MOTOR/TRANSAXLE ASSEMBLY:

νThese items are all prelubricated, sealed, and require no subsequent lubrication.

TO REPLACE THE MOTOR BRUSHES:

1.Disassemble the Shuttle.

2.Place the rear frame assembly on something that will support it.

3.Remove the four Phillips-head screws from the rear shroud.

4.Use a small right angle screwdriver to unscrew the top motor brush cap. See fgure 22.

5.Remove the motor brush.

6.Examine the motor brush. If the brush is worn or damaged, replace both brushes.

7.Reinstall the brush and the motor brush cap.

8.Reinstall the shroud.

9.Turn over the rear frame assembly.

10.Unscrew the other motor brush cap. Inspect and replace as necessary.

11.Reassemble the scooter.

MOTOR BRUSH CAPS

FIGURE 22. MOTOR BRUSH REPLACEMENT

CONSOLE, CHARGER, AND ELECTRONIC CONTROLLER:

νKeep these areas free of moisture.

νIf any of these items do become exposed to moisture, let them dry thoroughly before operating your Shuttle again.

STORAGE:

See VI. “Batteries and Charging,” and refer to “How should I store my Shuttle and its batteries?”

30

Shuttle

Image 30

Contents Wheel Scooters F E T Y G U I D E L I N E S N T E N T S P Y R I G H T N T R O D U C T I O N Elevators S a F E T YDoors Ramps and Other InclinesDriving Surfaces Normal Driving PositionSafety Precautions I . E M I / R F EMI/RFI Frequently Asked Questions FaqsWhere do radio waves come from? EMI/RFI WarningsWhat is the FDA doing about the problem? What should I do if my Shuttle moves unexpectedly?Specification S Weight Capacity16.5-18.5 985˚ 34.5 Control Console Assembly E S C R I P T I O NBattery Condition Meter Key SwitchSpeed Adjustment Dial Light Switch OptionalRear Section Onboard Battery Charger not shownBattery Charger Fuse Not shown Ammeter and Charger CordManual Freewheel Lever Electronic Controller Assembly not shownMainCircuit Breaker Anti-Tip WheelsHow does the charger work? B a T T E R I E S a N D C H a R G I N GFollow these easy steps to charge your batteries safely Can I USE a Different CHARGER?What type and size of battery should I use? Use these specifications to reorder deep-cycle batteriesHow can I get maximum range or distance per charge? To change a battery in your Shuttle Why do my new batteries seem weak?How can I ensure maximum battery life? How should I store my Shuttle and its batteries?What about public transportation? Getting on Your Shuttle PRE-RIDE Adjustments and ChecksI . O P E R a T I O N Operating Your ShuttleGetting OFF of Your Shuttle Electric Seat Height Adjustment Optional Tiller Angle AdjustmentSeat Height Adjustment I I . C O M F O R T a D J U S T M E N T SArmrest Width Adjustment Remove These Bolts to Adjust Seat PositionDisassembly AssemblyD I S a S S E M B L Y a N D a S S E M B L Y Frame Lock Lever P T I O N a L a C C E S S O R I E S B a S I C Troubleshooting What if all the systems on my Shuttle seem to be dead?What if the motor runs but my Shuttle does not move? I . C a R E a N D M a I N T E N a N C E CONSOLE, CHARGER, and Electronic Controller Axle Bearings and the MOTOR/TRANSAXLE AssemblyTo Replace the Motor Brushes StorageONE Year Limited Warranty THREE-YEAR Limited WarrantyTHREE-YEAR Warranty Exceptions Warranty ExclusionsI I . W a R R a N T Y T E S T E S