Pride Mobility PMV5001 manual Wheel Replacement, If your PMV is equipped with a solid tire insert

Page 37
HUB

I X . C A R E A N D M A I N T E N A N C E

WHEEL REPLACEMENT

 

 

If your PMV is equipped with pneumatic tires and

 

 

you have a flat tire, you can have the tube replaced.

DRIVE WHEEL

AXLE KEY

If your PMV is equipped with a solid tire insert,

NUT

 

either the solid insert or the entire wheel must be

 

 

replaced depending on the model. Contact your

 

 

authorized Pride Provider for information regarding

 

 

replacement wheels for your PMV.

 

AXLE SLOT

 

 

WARNING! Wheels on your PMV

 

 

should only be serviced/replaced by

 

 

an authorized Pride Provider or quali-

 

 

fied technician.

DRIVE WHEEL WASHER

 

WARNING! Completely deflate pneu-

Figure 22. Drive Wheel Removal

matic tires before dismantling the

rim or attempting repair.

 

 

WARNING! Be sure that the key is removed from the key switch and the PMV is not in freewheel mode before

 

performing this procedure.

REAR RIM HALF

 

 

 

WARNING! When changing a tire,

TIRE

 

remove only the center lug nut, then

 

remove the wheel. If any further dis-

 

 

assembly is required, deflate the tire

 

 

completely or it may explode.

 

Follow these easy steps for a quick and safe repair

TUBE

of both pneumatic and solid tires:

 

1.

Remove the key from the key switch.

FRONT

2.

Elevate the side of the PMV from which you are

RIM

 

removing the tire. Place wooden blocks under the

HALF

 

frame to elevate the PMV.

WARNING! Completely deflate

3.

the tire before attempting repair!

If you are changing a pneumatic tire, completely

WASHERS

 

deflate it before removing the wheel.

4.

Remove the drive wheel nut and washer from the

NUTS

 

axle. See figure 22.

 

5.

Pull the wheel off the axle.

Figure 23. Drive Wheel Assembly

6.

Remove the nuts and washers and separate the

 

rim halves. See figure 23.

7.Remove the old tube from the pneumatic tire and replace it with a new tube or replace the entire assembly if it is a solid tire.

8.Reassemble the rim halves.

9.Slide the wheel back onto the axle. Make sure that the axle key is in the axle slot. See figure 22.

WARNING! Failure to ensure that the axle key is properly installed into the axle slot when mounting the wheel can result in electronic brake failure, personal injury, and/or product damage.

Hurricane

www.pridemobility.com

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Hurricane F E T Y G U I D E L I N E S N T E N T S Canada N T R O D U C T I O NS a F E T Y Product Safety SymbolsS a F E T Y S a F E T Y General Removable Parts PRE-RIDE Safety CheckModifications Weight Limitations Perform the following inspections prior to using your PMVTire Inflation Incline InformationMaximum Recommended Incline Angles Braking Information Cornering InformationCorrect Curb Approach Outdoor Driving SurfacesFreewheel Mode Inclement Weather PrecautionsStairs and Escalators DoorsElevators Battery Disposal and RecyclingLIFT/ELEVATION Products BatteriesPositioning Belts Motor Vehicle TransportGetting Onto and OFF of Your PMV Reaching and BendingALCOHOL/SMOKING Prescription DRUGS/PHYSICAL LimitationsElectromagnetic and Radio Frequency Interference EMI/RFI Tiller Console I . Y O U R P MTo Move Backward use either of the following To Move Forward use either of the followingStatus LED Motor/Transaxle Assembly Not Shown B a T T E R I E S a N D C H a R G I N G Reading Your Battery VoltageBatteries and Charging Charging Your BatteriesHow does the charger work? Follow these easy steps to charge your batteries safelyWhat if my PMV’s batteries won’t charge? Can I use a different charger? How can I ensure maximum battery life?How often must I charge the batteries? Why do my new batteries seem weak? How do I change a battery?What about public transportation? P E R a T I O N PRE-RIDE Adjustments and ChecksBefore Getting on Your PMV Getting Onto Your PMVGetting OFF of Your PMV Power Down Timer FeatureSeat Rotation Adjustment Tiller Angle AdjustmentFRONT-TO-BACK Seat Adjustment Seatback AdjustmentSeat Height Adjustment Armrest Angle AdjustmentChanging the seat height System 2 Operation with power seat switch only Power Seat OptionalI . D I S a S S E M B L Y a N D a S S E M B L Y DisassemblyToggle Latch Release Frame Sections AssemblyDiagnostic Flash Codes I I . B a S I C TroubleshootingWhat if the main circuit breaker repeatedly trips? C a R E a N D M a I N T E N a N C E If your PMV is equipped with a solid tire insert Wheel ReplacementFollow these easy steps for a quick and safe repair Both pneumatic and solid tiresNylon Lock NUT Replacement Wiring HarnessesFuse Replacement ABS Plastic ShroudsStoring Your PMV Light Bulb ReplacementDisposal of Your PMV A R R a N T Y Service Checks and Warranty Service Warranty ExclusionsExclusions also include components with damage caused by Implied WarrantiesP E N D I X I Specification S P E N D I X I Specification S T E S T E S T E S INFMANU2635
Related manuals
Manual 2 pages 53.24 Kb
Top Page Image Contents