Pride Mobility Elite 6 manual Seat Position, To change the seat position

Page 14

V . C O M F O R T A D J U S T M E N T S

Seat Position

You can move the seat forward or backward by changing the seat base mounting position.

To change the seat position:

1.Turn off the power to the controller.

2.Make sure the power chair is in drive mode.

3.Unplug the controller connector(s) from the power base.

4.Remove the seat from the power base.

5.Remove the screws and washers from the bottom of the seat plate. See figure 9.

6.Slide the seat plate forward or backward, aligning the holes in the plate with the corresponding holes on the seat base. You must move both sides of the seat forward or backward the same number of holes.

WARNING! Changing the position of the seat can cause instability. Do not change your seating configuration without first contacting Pride Mobility Products or your authorized Pride Provider.

WARNING! After any adjustments, repairs, or service and before use, make sure that all attaching hardware is tightened securely to prevent injury and/or equipment damage.

7.Reinstall the screws and washers to the seat plate and tighten the hardware firmly.

8.Reinstall the seat.

9.Reconnect the controller to the power base.

SEAT BASE

SEAT PLATE

WASHER

SCREW

WARNING! The center of gravity of your power chair was factory set to a position that meets the needs of the demographic majority of users. Your authorized Pride Provider has evaluated your power chair and made any necessary adjustments to suit your specific requirements. Adjusting the seat position can cause instability. Do not change your seating configuration without first contacting Pride Mobility Products or your authorized Pride Provider.

Figure 9. Seat Position Adjustment

14

www.pridemobility.com

Jazzy Elite 6

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Jazzy F E T Y G U I D E L I N E S Quick Reference InformationLanguage Usage IIIVII PURCHASER’S Agreement SafetyN T R O D U C T I O N Shipping and DeliveryUnited Kingdom Australia Product Safety Symbols S a F E T YPre-Ride Safety Check General GuidelinesJazzy Elite 6 Power Chair I . Y O U R P O W E R C H a I RJazzy Elite 6 Power Base Electrical Components Jazzy Elite 6 Electrical ComponentsManual Freewheel Levers To engage or disengage the drive motorsTo install the seat Initial AssemblySeat Installation A S S E M B L YO M F O R T a D J U S T M E N T S Comfort AdjustmentsSeat Height Adjustment Seat Position To change the seat positionArmrest Width Adjustment Seatback Angle AdjustmentManual Recline Seatback Adjustment Armrest Angle AdjustmentController Position Foot Platform Height AdjustmentTo adjust the foot platform height To extend the controllerElevating Leg Rests Foot Platform Angle AdjustmentSwing-away Footrests Positioning Belt To install the positioning beltTo adjust the positioning belt for operator comfort To release the positioning beltCharging the Batteries B a T T E R I E S a N D C H a R G I N GBatteries and Charging Battery Break-in Frequently Asked Questions FAQs„ Infrequent Use Why do my new batteries seem weak?„ Daily Use How can I get maximum range or distance per charge?What about public transportation? How can I ensure maximum battery life?How should I store my power chair and its batteries? What about shipping?Temperature Care and MaintenanceShould your power chair come in contact with water I . C a R E a N D M a I N T E N a N C ETo check the brakes Daily ChecksWeekly Checks Monthly ChecksWheel Replacement Disposal of Your Power ChairCleaning and Disinfection Yearly ChecksBattery Replacement You may need the following to change your batteriesBattery Installation Seat Removed for Clarity When to Contact Your Authorized Pride Provider for Service To replace the batteriesCorrective Maintenance T E S Page Date Inspected Inspector Product Serial #
Top Page Image Contents