Quantum INFMANU2924, 610 A S S E M B L Y O M F O R T a D J U S T M E N T S, Comfort Adjustments

Page 13

I V . A S S E M B L Y

V . C O M F O R T A D J U S T M E N T S

Power Seat Option Installation

Your power chair may be equipped with the power seat option. While the seat itself may be any one of the styles offered for this model, the way the seat base attaches to the power base is different.

To install the power seat:

l. Align the post on the bottom of the power seat base over the hole in the power seat actuator.

2. Slide the post into the actuator and push the friction lock lever forward.

3. Connect the power seat cable to the power base.

4. Tilt the seat back and slide the rear extension onto the power seat base.

5. Lower the front extrusion onto the power seat base until the seat locks into place.

6. Flip down the seat latch safety.

7. Install the controller.

NOTE: Refer to V. “Comfort Adjustments” for more information on controller installation and adjustment.

WIRE TIES

Figure 13. Controller Routed on a Contour Seat

COMFORT ADJUSTMENTS

After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to increase your comfort, such as seat height and angle, armrest angle, foot platform height and angle, and controller position. If your power chair is equipped with power positioning options, refer to the information supplied in supplemental manuals or contact your Quantum Rehab Provider.

WARNING! The center of gravity of your power chair was factory set to a position that meets the needs of the demographic majority of users. Your Quantum Rehab Provider has evaluated your power chair and made any necessary adjustments to suit your specific requirements. Do not change your seating configuration without first contacting Pride Mobility Products or your Quantum Rehab Provider.

WARNING! Some power chair components are heavy. You may need assistance to lift or carry them. Please refer to “Appendix I - Specifications” for specific component weights before you disassemble the power chair.

WARNING! Remove the occupant from the power chair before making any adjustments.

You may need the following to make comfort adjust- ments:

metric/standard socket set and ratchet adjustable wrench

thread lock

Seat Height and Seat Angle Adjustment

 

You can change the seat height to one of four positions

 

in 1-in. (2.54-cm) increments by raising the front and

 

rear trapeze bars. If you raise or lower only one trapeze

 

bar (front or rear), you can also change the seat base

Figure 15. Seat Height Adjustment - Seat Latch Safety

angle (dump).

To change the seat height:

1. Turn off the power to the controller.

FRICTION LOCK

LEVER

POWER SEAT

ACTUATOR

Figure 14. Power Seat Actuator

2. Loosen the rear shroud fasteners and remove the rear shroud. See figure 6.

3. Disconnect the controller connector(s) from the power base. See figure 7.

4. Flip up the seat latch safety. See figure 15.

5. Squeeze the seat latch and release the seat from the front trapeze bar. See figure 15.

6. Slide the seat forward and remove it from the power base. 7. Loosen the screws that attach the trapeze bars to the

seat posts. See figure 16.

8. Remove the retaining clips that secure the seat posts to the power base. See figure 16.

9. Move the trapeze bars up or down to the desired height.

10. Reinstall the retaining clips from step 8.

11. Remove each screw from the trapeze bars and apply thread lock.

12. Reinstall each screw into the trapeze bars and tighten.

13. Reinstall the seat and flip down the seat latch safety. 14. Reconnect the controller connector(s) to the power base. 15. Reinstall the rear shroud and tighten the fasteners.

SCREWS

TRAPEZE BARS

 

SEAT POSTS

SEAT POSTS

 

 

RETAINING

 

CLIPS

RETAINING

 

CLIPS

 

Figure 16. Seat Height Adjustment - Trapeze Bars

Quantum 610 Series

www.pridemobility.com

23

24

www.pridemobility.com

Quantum 610 Series

Image 13
Contents Quantum N S I G N E S D E S E C U R I T E N T R O D U C T I O N S a F E T Y Product Safety SymbolsS a F E T Y General Guidelines Inclement Weather Precautions Freewheel ModeBraking Information Cornering InformationDoors Stairs and EscalatorsElevators Lift Systems/Elevation ProductsPrescription Drugs/Physical Limitations TransfersAlcohol/Smoking Quantum I . Y O U R P O W E R C H a I RElectrical Components To engage or disengage the drive motors Manual Freewheel LeversSeat Installation Initial AssemblyTo install the seat A S S E M B L YComfort Adjustments Power Seat Option InstallationSeat Height and Seat Angle Adjustment A S S E M B L Y O M F O R T a D J U S T M E N T SManual Recline Seatback Adjustment Armrest Angle AdjustmentSeatback Angle Adjustment Armrest Width AdjustmentFoot Platform Depth Adjustment Foot Platform Height AdjustmentPower Elevating Seat Optional Foot Platform Angle AdjustmentCharging the Batteries Batteries and ChargingFrequently Asked Questions Battery Break-inTemperature Care and MaintenanceI . C a R E a N D M a I N T E N a N C E General GuidelinesCleaning and Disinfection Disposal of Your Power ChairWheel Replacement Daily ChecksWhen to See Your Quantum Rehab Provider for Service Battery ReplacementCorrective Maintenance To replace the batteriesT E S T E SN O T E S Page Quality Control Quantum
Related manuals
Manual 59 pages 42.17 Kb