Quantum 1103 Series, 1103 Ultra 2SP manual Seat Installation, To install the seat

Page 22

I V . A S S E M B L Y

Seat Installation

It may be necessary to install the seat either prior to initial oper- ation or after transporting your power chair. Most seats are attached to the power base with the Universal Mounting System (UMS). The UMS consists of universal parts that may be attached to any medium-back or high-back seat, regardless of seat width or seat depth. The two main components are alumi- num extrusions mounted to the seat base. These extrusions attach to the power seat frame (see figure 11) or to a pair of trapeze bars that are mounted to the power base (see figure 12).

NOTE: If your power chair is equipped with a Synergy Seat or a TRU-Balance Power Positioning System, refer to the information provided in separate manuals.

WARNING! Do not pick up the seat frame by the armrests. They are free to pivot, and you may lose control of the seat if they do so.

To install the seat:

1.Raise the power elevating seat actuator up 2 in. (5 cm) to allow for sufficient clearance.

2.Tilt the seat back and slide the rear extrusion onto the power seat frame or rear trapeze bar.

3.Lower the front extrusion onto the power seat frame or front trapeze bar until the seat locks into place.

4.Flip the seat latch safety down. See figure 11.

WARNING! Make sure the seat latch safety is flipped down before using your power chair.

5.Install the controller into one of the armrests. See V. “Com- fort Adjustments”.

6.Loosen the rear shroud fasteners and remove the rear shroud.

7.Route the controller connector to the back of the power base and secure the controller harness to the armrest receiver with wire ties. See figure 13 or 14.

MANDATORY! Prevent controller harness damage! Avoid routing the controller harness on the outside of the armrest pad. Route the harness under the armrest or toward the inside of the armrest pad. Use correct tie-down points for the controller harness to prevent the harness from getting caught in the drive tires, pinched in the seat frame, or damaged when passing through doorways.

8.Plug the controller connectors into the power module and connect the battery connector. See figure 7.

9.Reinstall the rear shroud and tighten the fasteners.

SEAT LATCH

 

SAFETY

 

FRICTIONLOCK

 

LEVER

POWER SEAT FRAME

 

Figure 11. UMS – Power Elevating Seat System

FRONT EXTRUSION

 

 

REAR TRAPEZE

 

BAR

FRONT TRAPEZE BAR

REAR EXTRUSION

 

Figure 12. UMS – Optional Seating System

22

www.pridemobility.com

Quantum 1103 Ultra

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Quantum F E T Y G U I D E L I N E S Quick Reference InformationN T E N T S IIIPURCHASER’S Agreement SafetyN T R O D U C T I O N Shipping and DeliveryProduct Safety Symbols S a F E T YS a F E T Y S a F E T Y S a F E T Y General Guidelines Pre-Ride Safety CheckModifications Tire Inflation Weight LimitationsIncline Information Braking Information Freewheel ModeCornering Information Public Streets and Roadways Outdoor Driving Surfaces Inclement Weather PrecautionsStationary Obstacles Steps, Curbs, etc Elevators Stairs and EscalatorsDoors Lift/Elevation ProductsBatteries Positioning BeltsRemovable Parts Preventing Unintended Movement Transfers Reaching and BendingPrescription Drugs/Physical Limitations Alcohol/Smoking Quantum 1103 Ultra Power Chair I . Y O U R P O W E R C H a I RQuantum 1103 Ultra Power Base Electrical Components Quantum 1103 Ultra Electrical Components Manual Freewheel Levers To engage or disengage the drive motorsInitial Assembly A S S E M B L YSeat Installation To install the seatA S S E M B L Y O M F O R T a D J U S T M E N T S Comfort AdjustmentsYou may need the following to make comfort adjustments To change the seat heightTo adjust the seatback angle Seat Position AdjustmentManual Recline Seatback Adjustment To change the positionArmrest Angle Adjustment Seatback Angle AdjustmentArmrest Width Adjustment Armrest Height AdjustmentTo extend the controller Controller PositionTo change the controller position To adjust the foot platform depth Foot Platform Height AdjustmentFoot Platform Depth Adjustment To raise or lower the foot platformTo adjust the anti-tip wheels Foot Platform Angle AdjustmentTo adjust the foot platform angle Anti-Tip WheelsTo change the seat height through toggle switch Power Elevating Seat OptionalTo use the swivel feature Positioning Belt To install the positioning beltTo adjust the positioning belt for operator comfort To release the positioning beltBatteries and Charging B a T T E R I E S a N D C H a R G I N GCharging the Batteries Battery Break-in Frequently Asked Questions FAQsInfrequent Use Why do my new batteries seem weak?Daily Use How can I get maximum range or distance per charge?What about public transportation? How can I ensure maximum battery life?How should I store my power chair and its batteries? What about shipping?Temperature Care and MaintenanceShould your power chair come in contact with water I . C a R E a N D M a I N T E N a N C ETo check the brakes Daily ChecksWeekly Checks Monthly ChecksWheel Replacement Disposal of Your Power ChairCleaning Instructions StorageBattery Replacement I . C a R E a N D M a I N T E N a N C EQuantum 1103 Ultra Battery Connections To replace the batteriesWhen to See Your Quantum Rehab Provider for Service Corrective MaintenanceI I . W a R R a N T Y Service Checks and Warranty Service Reconditioned Units WarrantyWarranty Exclusions Exclusions also include components with damage caused byP E N D I X I Specification S SpecificationsQuantum 1103 Ultra Dimensions and Ground Clearance T E S Quality Control Quantum 1103 Ultra Series Product Serial #
Top Page Image Contents