Quantum 1103 Series, 1103 Ultra 2SP manual O M F O R T a D J U S T M E N T S, Comfort Adjustments

Page 24

V . C O M F O R T A D J U S T M E N T S

COMFORT ADJUSTMENTS

After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to increase your comfort, such as seat height and angle, armrest angle, foot platform height and angle, and controller position.

NOTE: If your power chair is equipped with a Specialty Seat, Synergy Seat, or TRU-Balance Power Position- ing System, refer to the seat adjustment information contained in separate manuals. If your power chair is equipped with a medium-back, a high-back, a reclining seat, or a power elevating seat, refer to the following information.

WARNING! The center of gravity of your power chair was factory set to a position that meets the needs of the demographic majority of users. Your Quantum Rehab Provider has evaluated your power chair and made any necessary adjustments to suit your specific requirements. Do not change your seating configuration without first contacting Pride Mobility Products or your Quantum Rehab Provider.

WARNING! Some power chair components are heavy. You may need assistance to lift or carry them. Please refer to the specifications table for specific component weights before you disassemble the power chair.

WARNING! Remove the occupant from the power chair before making any adjustments.

You may need the following to make comfort adjustments:

metric/standard socket set and ratchet adjustable wrench

thread lock metric/standard hex key set

Seat Height and Seat Angle Adjustment

(Optional Trapeze Bar System)

You can change the seat height to one of two positions by raising the front and rear trapeze bars. If you raise or lower only one trapeze bar (front or rear), you can also change the seat base angle (dump).

To change the seat height:

1.Turn off the power to the controller.

2.Loosen the rear shroud fasteners and remove the rear shroud. See figure 6.

3.Disconnect the controller connectors from the power module. See figure 7.

4.Flip up the seat latch safety. See figure 15.

5.Squeeze the seat latch and release the seat from the front trapeze bar.

6.Slide the seat forward and remove it from the power base.

7.Loosen the screws that attach the trapeze bars to the seat posts. See figure 16.

8.Remove the retaining clips that secure the seat posts to the power base. See figure 16.

9.Move the trapeze bars up or down to the desired height.

Figure 15. Seat Height Adjustment – Seat Latch Safety

SCREWS

SCREWS

 

TRAPEZE BAR

TRAPEZE BAR

 

 

SEAT POST

SEAT POSTS

RETAINING

CLIPS

Figure 16. Trapeze Bar Location

24

www.pridemobility.com

Quantum 1103 Ultra

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Quantum F E T Y G U I D E L I N E S Quick Reference InformationN T E N T S IIISafety N T R O D U C T I O NPURCHASER’S Agreement Shipping and DeliveryProduct Safety Symbols S a F E T YS a F E T Y S a F E T Y S a F E T Y Pre-Ride Safety Check General GuidelinesModifications Weight Limitations Tire InflationIncline Information Freewheel Mode Braking InformationCornering Information Inclement Weather Precautions Public Streets and Roadways Outdoor Driving SurfacesStationary Obstacles Steps, Curbs, etc Stairs and Escalators DoorsElevators Lift/Elevation ProductsPositioning Belts BatteriesRemovable Parts Preventing Unintended Movement Reaching and Bending TransfersPrescription Drugs/Physical Limitations Alcohol/Smoking Quantum 1103 Ultra Power Chair I . Y O U R P O W E R C H a I RQuantum 1103 Ultra Power Base Electrical ComponentsQuantum 1103 Ultra Electrical Components Manual Freewheel Levers To engage or disengage the drive motors Initial Assembly A S S E M B L YSeat Installation To install the seatA S S E M B L Y Comfort Adjustments You may need the following to make comfort adjustmentsO M F O R T a D J U S T M E N T S To change the seat heightSeat Position Adjustment Manual Recline Seatback AdjustmentTo adjust the seatback angle To change the positionSeatback Angle Adjustment Armrest Width AdjustmentArmrest Angle Adjustment Armrest Height AdjustmentController Position To extend the controllerTo change the controller position Foot Platform Height Adjustment Foot Platform Depth AdjustmentTo adjust the foot platform depth To raise or lower the foot platformFoot Platform Angle Adjustment To adjust the foot platform angleTo adjust the anti-tip wheels Anti-Tip WheelsPower Elevating Seat Optional To change the seat height through toggle switchTo use the swivel feature To install the positioning belt To adjust the positioning belt for operator comfortPositioning Belt To release the positioning beltB a T T E R I E S a N D C H a R G I N G Batteries and ChargingCharging the Batteries Battery Break-in Frequently Asked Questions FAQsWhy do my new batteries seem weak? Daily UseInfrequent Use How can I get maximum range or distance per charge?How can I ensure maximum battery life? How should I store my power chair and its batteries?What about public transportation? What about shipping?Care and Maintenance Should your power chair come in contact with waterTemperature I . C a R E a N D M a I N T E N a N C EDaily Checks Weekly ChecksTo check the brakes Monthly ChecksDisposal of Your Power Chair Cleaning InstructionsWheel Replacement StorageBattery Replacement I . C a R E a N D M a I N T E N a N C EQuantum 1103 Ultra Battery Connections To replace the batteriesWhen to See Your Quantum Rehab Provider for Service Corrective MaintenanceI I . W a R R a N T Y Reconditioned Units Warranty Warranty ExclusionsService Checks and Warranty Service Exclusions also include components with damage caused byP E N D I X I Specification S SpecificationsQuantum 1103 Ultra Dimensions and Ground Clearance T E S Quality Control Quantum 1103 Ultra Series Product Serial #
Top Page Image Contents