Pride Mobility INFMANJ2828 manual Seat Installation, To install the seat, Base. See figure

Page 22

I V . A S S E M B L Y

Seat Installation

It may be necessary to install the seat either prior to initial operation or after transporting your power chair. Most seats are attached to the power base with the Uni- versal Mounting System (UMS). The UMS consists of universal parts that may be attached to any medium- back or high-back seat, regardless of seat width or seat depth. The two main components are aluminum extru- sions mounted to the seat base. These extrusions attach to a pair of trapeze bars that are mounted to the power base. See figure 11.

WARNING! Do not pick up the seat frame by the armrests. They are free to pivot, and you may lose control of the seat if they do so.

To install the seat:

1.Tilt the seat back and slide the rear extrusion onto the rear trapeze bar. See figure 11.

2.Lower the front extrusion onto the front trapeze bar until the seat locks into place.

3.Flip the seat latch safety down.

REAR EXTRUSION

FRONT

EXTRUSION

SETSCREW

SEAT

LATCH

SAFETY

TRAPEZE BARS

Figure 11. Universal Mounting System

WARNING! Make sure the seat latch safety is flipped down before using

your power chair.

SIDE TABS

 

4. Install the controller into one of the armrests.

 

 

Tighten the setscrew. See figure 11.

 

 

5. Route the controller harness so that it cannot be

 

 

pinched in the seat hinge.

 

 

MANDATORY! Prevent controller harness

 

 

damage! Avoid routing the controller har-

 

 

ness on the outside of the armrest pad.

SIDE TABS

 

Route the harness under the armrest or

 

toward the inside of the armrest pad. Use

 

BACK TABS

correct tie-down points for the controller

HARNESS ACCESS POINT

harness to prevent the harness from get-

 

 

ting caught in the drive tires, pinched in

Figure 12. Rear Shroud

 

the seat frame, or damaged when passing

 

 

 

through doorways.

 

 

6.

Gently push down and pull backward at the harness

 

 

access point on the rear shroud until it releases. See

 

 

figure 12.

 

 

 

 

 

 

7.

Remove the rear shroud.

 

 

 

 

 

8.

Plug the controller connector(s) into the power

 

 

base. See figure 7.

 

 

 

 

 

9.

Reinstall the rear shroud by aligning the side and

 

 

back tabs with the holes in the main shroud. Gently

 

 

push down and forward until all four tabs lock into

 

 

place.

 

 

 

 

 

 

 

10.

Secure

the

controller

harness

to

the

armrest

WIRE TIES

 

receiver with one or more wire ties. See figure 13.

 

Figure 13. Controller Harness Routing

 

 

 

 

 

 

 

 

22

www.pridemobility.com

Jazzy 600 Series

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Jazzy F E T Y G U I D E L I N E S Quick Reference InformationN T E N T S IIIPURCHASER’S Agreement SafetyN T R O D U C T I O N Shipping and DeliveryProduct Safety Symbols S a F E T YS a F E T Y S a F E T Y S a F E T Y General Guidelines Pre-Ride Safety CheckModifications Tire Inflation Weight LimitationsIncline Information Braking Information Freewheel ModeCornering Information Public Streets and Roadways Outdoor Driving Surfaces Inclement Weather PrecautionsStationary Obstacles Steps, Curbs, etc Elevators Stairs and EscalatorsDoors Lift Systems/Elevation ProductsBatteries Motor Vehicle TransportPositioning Belts Removable Parts Preventing Unintended MovementReaching and Bending TransfersPrescription Drugs/Physical Limitations Alcohol/SmokingI . Y O U R P O W E R C H a I R Jazzy 600 SeriesJazzy 600 Series Power Base Electrical ComponentsJazzy 600 Series Electrical Components Manual Freewheel Levers To engage or disengage the drive motorsInitial Assembly A S S E M B L YTo install the seat Seat InstallationBase. See figure Seat Height and Seat Angle Adjustment Comfort AdjustmentsYou may need the following to make comfort adjustments O M F O R T a D J U S T M E N T STo adjust the recline angle Seat Position AdjustmentManual Recline Seatback Adjustment To change the seat positionArmrest Angle Adjustment Seatback Angle AdjustmentArmrest Width Adjustment Armrest Height AdjustmentTo extend the controller Controller PositionTo change the controller position Foot Platform Angle Adjustment Foot Platform Height AdjustmentFoot Platform Depth Adjustment Positioning BeltBatteries and Charging B a T T E R I E S a N D C H a R G I N GCharging the Batteries Battery Break-in Frequently Asked Questions FAQsInfrequent Use Why do my new batteries seem weak?Daily Use How can I get maximum range or distance per charge?What about public transportation? How can I ensure maximum battery life?How should I store my power chair and its batteries? What about shipping?Temperature Care and MaintenanceShould your power chair come in contact with water I . C a R E a N D M a I N T E N a N C ETo check the brakes Daily ChecksWeekly Checks Monthly ChecksWheel Replacement Disposal of Your Power ChairCleaning and Disinfection StorageBattery Replacement Jazzy 600 Drive WheelBattery Installation Corrective Maintenance When to See Your Authorized Pride Provider for ServiceTo replace the batteries T E S T E S T E S T E S T E S Page Quality Control Jazzy 600 Series Product Serial #
Top Page Image Contents