Pride Mobility Jet 7 owner manual Anti-Tip Wheels Adjustment, To adjust the anti-tip wheels

Page 26

V I . C O M F O R T A D J U S T M E N T S

Anti-Tip Wheels Adjustment

The anti-tip wheels are designed to give your power chair increased stability on rough surfaces. The anti-tip wheels are preset at the factory for smooth surfaces or indoor use only. If you plan on using your power chair on rough surfaces, it may be necessary to adjust the anti-tip wheels to better suit your needs. The anti-tip wheels may need adjustment if the following occurs:

!When coming to a stop, your power chair tips forward excessively.

!The anti-tip wheels constantly rub the ground.

WARNING! Consult your authorized Pride Provider before attempting to change the anti-tip wheel height! Changing the anti-tip wheel height affects handling under acceleration!

WARNING! The higher you raise the anti-tip wheels, the more you increase your power chair’s tendency to tilt forward while decelerating. You can compensate for this by having your authorized Pride Provider make a small adjustment to the pre-programmed deceleration setting in the controller or by moving the seat assembly farther to the back of your power chair.

PROHIBITED! Do not remove the anti-tip wheels.

NOTE: Each drive tire must be inflated to 35 psi (2.4 bar) if equipped with pneumatic tires.

To adjust the anti-tip wheels:

1.Turn off the power to the controller.

2.Make sure that the manual freewheel levers are in the drive position.

3.Disconnect the controller from the electronics tray.

4.Remove the seat.

5.Unplug the left and right motor connectors.

6.Unplug and remove both battery boxes.

7.Remove both left and right shrouds. Two screws fasten each shroud section to the frame. These screws are located on the top of the shroud near the seat post holes.

8.Locate the anti-tip adjustment nut. See figure 27.

9.Turn the adjustment nut counterclockwise to lower the anti-tip wheels and soften the suspension, or turn the adjustment nut clockwise to raise the anti-tip wheels and stiffen the suspension.

ANTI-TIP ADJUSTMENT NUT

NOTE: Make the same adjustment to both anti-tip wheels.

Figure 27 Anti-tip Wheel adjustment

10.Reinstall the left and right shrouds.

11.Reinstall both battery boxes and plug in the battery connectors.

12.Plug the left and right motor connectors into their receptacles.

13.Reinstall the seat.

14.Connect the controller to the electronics tray.

26

www.pridemobility.com

Jet 7

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Stylish Design and Premium Performance F E T Y G U I D E L I N E S N T E N T S IIIPURCHASER’S Agreement SafetyN T R O D U C T I O N Information ExchangePride Owners Club My Authorized Pride Provider isModifications Pre-Ride Safety CheckS a F E T Y Incline Information Weight LimitationsTire Inflation Outdoor Driving Surfaces Braking InformationCornering Information Public Streets and Roadways Stairs and Escalators Freewheel ModeStationary Obstacles Steps, Curbs, etc Elevators TransfersDoors Lift/Elevation ProductsPositioning Belts Inclement Weather PrecautionsMotor Vehicle Transport Reaching and BendingRemovable Parts BatteriesAlcohol Electromagnetic and Radio Frequency Interference EMI/RFI Your Power Chair I . Y O U R P O W E R C H a I RJet 7 Power Base Specifications Electrical Components Electronics TrayManual Freewheel Levers To engage or disengage the drive motorsTo install the seat Initial AssemblySeat Installation A S S E M B L YDisassembly I S a S S E M B L YTo disassemble your power chair Removing the Trapeze BarsRemoving Battery Boxes C O M F O R T a D J U S T M E N T S Comfort AdjustmentsSeat Height and Seat Angle Adjustment To change the seat heightArmrest Width Adjustment Seatback Angle AdjustmentArmrest Height Adjustment Armrest Angle AdjustmentController Extension Foot Platform Height AdjustmentFoot Platform Angle Adjustment Controller PositionAnti-Tip Wheels Adjustment To adjust the anti-tip wheelsVSI consists I . O P E R a T I O NVSI Electronic Controller JoystickRed lights only lit or slow flash Charge batteries as Battery Condition MeterOn/Off Key Speed/Profile KeysCharger Inhibit Connector Actuator ConnectorController Connector Horn KeyVSI Error Codes Thermal RollbackCharging Your Batteries I I . B a T T E R I E S a N D C H a R G I N GBatteries and Charging Off-board Charger Battery Break-inFrequently Asked Questions FAQs Daily Use Infrequent UseWhat about public transportation? How can I ensure maximum battery life?How should I store my power chair and batteries? What about shipping?Temperature Care and MaintenanceShould your power chair come in contact with water C a R E a N D M a I N T E N a N C EMonthly Checks Daily ChecksWeekly Checks Yearly ChecksWheel Replacement Disposal of Your Power ChairCleaning and Disinfection Battery Replacement To replace the batteriesWhen to See Your Authorized Pride Provider for Service Corrective MaintenanceA R R a N T Y Service Checks and Warranty Service Implied WarrantiesT E S Quality Control Model Jet

Jet 7 specifications

The Pride Mobility Jet 7 is a revolutionary powered mobility solution designed for users seeking both independence and convenience. This advanced mobility scooter is ideal for those with limited mobility, providing enhanced stability, comfort, and maneuverability. With its sleek design and high-performance features, the Jet 7 stands out in the market.

One of the standout features of the Jet 7 is its innovative XLR technology, which ensures a smooth and stable ride. This system incorporates an extended wheelbase and advanced suspension to provide superior stability, allowing users to navigate various terrains with ease. Whether it’s a bumpy sidewalk or a gravel path, the Jet 7 handles it seamlessly.

The Jet 7's sleek and stylish contemporary design allows users to travel in style. It is available in various attractive colors, making it a customizable choice for every individual. The scooter's lightweight frame and compact size make it easy to transport, whether it’s in the trunk of a car or on public transportation.

Comfort is a significant focus of the Jet 7. It features a fully adjustable and contoured seat with ample cushioning. The adjustable armrests provide additional support, enabling users to find the perfect position for their individual comfort. This ergonomic design reduces fatigue during longer rides and enhances the overall experience.

Equipped with powerful motors, the Jet 7 offers impressive speed and range. Users can travel distances up to 15 miles on a single charge, making it suitable for errands or longer outings. The easy-to-use joystick control provides intuitive steering, allowing users to navigate tight spaces with precision.

Safety is paramount in the design of the Jet 7. It is equipped with anti-tip wheels, ensuring stability on inclines and declines. The scooter also features bright LED lights for improved visibility during low-light conditions, keeping users safe while on the go.

Furthermore, the Jet 7 is designed with serviceability in mind. It includes modular components that are easy to access, making maintenance straightforward for both users and technicians. This attention to detail ensures longevity and reliability, making it a trusted choice for mobility needs.

In conclusion, the Pride Mobility Jet 7 combines advanced technology, comfort, safety, and style to deliver an exceptional mobility experience. It empowers users to regain their independence while providing the means to explore the world around them with confidence. Whether for daily errands or weekend adventures, the Jet 7 is a prime example of how mobility devices can enhance quality of life.
Top Page Image Contents