Pride Mobility Jet 7 owner manual Battery Replacement, To replace the batteries

Page 38

I X . C A R E A N D M A I N T E N A N C E

5.Pull the wheel off the axle.

6.Remove the nuts and washers from the wheel hub. See figure 31.

7.Remove the old tube from the pneumatic tire and replace it with a new tube, or replace the entire solid wheel assembly.

8.Reassemble the rims and reinstall the nuts and washers.

9.Slide the wheel back onto the axle. Make sure the key is in the axle slot.

10.Reinstall the drive wheel nut and washer onto the axle and tighten.

11.Inflate the pneumatic tire to 35 psi (2.4 bar).

12.Remove the power chair from the blocks.

Battery Replacement

WARNING! Prevent injury. Do not replace battery when seat is occupied.

WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds. Wear goggles and gloves when handling batteries and wash hands after handling.

WARNING! Power chair batteries are heavy. See specifications table. If you are unable to lift that much weight, be sure to get help. Lifting beyond your capacity can result in personal injury.

WARNING! Prevent injury and/or equipment damage! Do not mix or match new and old batteries. If you encounter a situation where one battery needs to be replaced, then replace both batteries. Refer to the specifications table in this manual and the manual supplied with the battery charger for recommended type and capacities.

To replace the batteries:

1.Turn off the power to the controller.

2.Disconnect the controller from the electronics tray.

3.Remove the seat.

4.Remove the battery boxes and set them on a solid, flat surface.

5.Unfasten the battery box straps on the bottom of each box.

6.Lift up the top cover.

7.Remove the rubber covers from the terminals. Unscrew the terminal nuts and bolts and disconnect the battery wires from the battery terminals.

8.Remove the battery from the bottom cover.

9.Place the new battery into the bottom cover.

10.Connect the red battery wire to the (+) positive terminal and the black battery wire to the (-) negative terminal.

WARNING! Make sure you tighten the fasteners so that the connections are secure.

11.Place the rubber covers over the terminals.

12.Replace the top cover on each battery box.

13.Fasten the straps and make sure the connections are secure.

14.Position the battery terminals on the opposite side of the battery charger.

WARNING! If you do not position the battery terminals on the opposite side of the charger, you run the risk of shorting out the batteries and severely damaging your power chair!

15.Place the rear battery box back into the battery well.

16.Place the front battery box back into the battery well.

38

www.pridemobility.com

Jet 7

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Stylish Design and Premium Performance F E T Y G U I D E L I N E S N T E N T S IIIPURCHASER’S Agreement SafetyN T R O D U C T I O N Information ExchangePride Owners Club My Authorized Pride Provider isModifications Pre-Ride Safety CheckS a F E T Y Incline Information Weight LimitationsTire Inflation Outdoor Driving Surfaces Braking InformationCornering Information Public Streets and Roadways Stairs and Escalators Freewheel ModeStationary Obstacles Steps, Curbs, etc Elevators TransfersDoors Lift/Elevation ProductsPositioning Belts Inclement Weather PrecautionsMotor Vehicle Transport Reaching and BendingRemovable Parts BatteriesAlcohol Electromagnetic and Radio Frequency Interference EMI/RFI Your Power Chair I . Y O U R P O W E R C H a I RJet 7 Power Base Specifications Electrical Components Electronics TrayManual Freewheel Levers To engage or disengage the drive motorsTo install the seat Initial AssemblySeat Installation A S S E M B L YDisassembly I S a S S E M B L YTo disassemble your power chair Removing the Trapeze BarsRemoving Battery Boxes C O M F O R T a D J U S T M E N T S Comfort AdjustmentsSeat Height and Seat Angle Adjustment To change the seat heightArmrest Width Adjustment Seatback Angle AdjustmentArmrest Height Adjustment Armrest Angle AdjustmentController Extension Foot Platform Height AdjustmentFoot Platform Angle Adjustment Controller PositionAnti-Tip Wheels Adjustment To adjust the anti-tip wheelsVSI consists I . O P E R a T I O NVSI Electronic Controller JoystickRed lights only lit or slow flash Charge batteries as Battery Condition MeterOn/Off Key Speed/Profile KeysCharger Inhibit Connector Actuator ConnectorController Connector Horn KeyVSI Error Codes Thermal RollbackCharging Your Batteries I I . B a T T E R I E S a N D C H a R G I N GBatteries and Charging Off-board Charger Battery Break-inFrequently Asked Questions FAQs Daily Use Infrequent UseWhat about public transportation? How can I ensure maximum battery life?How should I store my power chair and batteries? What about shipping?Temperature Care and MaintenanceShould your power chair come in contact with water C a R E a N D M a I N T E N a N C EMonthly Checks Daily ChecksWeekly Checks Yearly ChecksWheel Replacement Disposal of Your Power ChairCleaning and Disinfection Battery Replacement To replace the batteriesWhen to See Your Authorized Pride Provider for Service Corrective MaintenanceA R R a N T Y Service Checks and Warranty Service Implied WarrantiesT E S Quality Control Model Jet

Jet 7 specifications

The Pride Mobility Jet 7 is a revolutionary powered mobility solution designed for users seeking both independence and convenience. This advanced mobility scooter is ideal for those with limited mobility, providing enhanced stability, comfort, and maneuverability. With its sleek design and high-performance features, the Jet 7 stands out in the market.

One of the standout features of the Jet 7 is its innovative XLR technology, which ensures a smooth and stable ride. This system incorporates an extended wheelbase and advanced suspension to provide superior stability, allowing users to navigate various terrains with ease. Whether it’s a bumpy sidewalk or a gravel path, the Jet 7 handles it seamlessly.

The Jet 7's sleek and stylish contemporary design allows users to travel in style. It is available in various attractive colors, making it a customizable choice for every individual. The scooter's lightweight frame and compact size make it easy to transport, whether it’s in the trunk of a car or on public transportation.

Comfort is a significant focus of the Jet 7. It features a fully adjustable and contoured seat with ample cushioning. The adjustable armrests provide additional support, enabling users to find the perfect position for their individual comfort. This ergonomic design reduces fatigue during longer rides and enhances the overall experience.

Equipped with powerful motors, the Jet 7 offers impressive speed and range. Users can travel distances up to 15 miles on a single charge, making it suitable for errands or longer outings. The easy-to-use joystick control provides intuitive steering, allowing users to navigate tight spaces with precision.

Safety is paramount in the design of the Jet 7. It is equipped with anti-tip wheels, ensuring stability on inclines and declines. The scooter also features bright LED lights for improved visibility during low-light conditions, keeping users safe while on the go.

Furthermore, the Jet 7 is designed with serviceability in mind. It includes modular components that are easy to access, making maintenance straightforward for both users and technicians. This attention to detail ensures longevity and reliability, making it a trusted choice for mobility needs.

In conclusion, the Pride Mobility Jet 7 combines advanced technology, comfort, safety, and style to deliver an exceptional mobility experience. It empowers users to regain their independence while providing the means to explore the world around them with confidence. Whether for daily errands or weekend adventures, the Jet 7 is a prime example of how mobility devices can enhance quality of life.
Top Page Image Contents