Pride Mobility Jazzy1133 Controller Position, To change the controller position, Anti-Tip Wheels

Page 27

V I . C O M F O R T A D J U S T M E N T S

Controller Position

You can position the controller for either left-hand or right-hand use.

To change the controller position:

1.Unplug the controller and the charger inhibit connectors from the back battery box. See figure 6.

2.Cut the wire tie(s) that attach the controller cable to the seat.

3.Use a hex key to loosen the setscrew underneath the armrest. See figure 25.

4.Slide the controller out of the armrest.

5.Loosen the setscrew underneath the other armrest.

6.Place the controller in the other armrest.

7.Tighten the setscrew.

8.Plug in the controller and the charger inhibit connectors to the back battery box.

9.Use a wire tie to secure the controller cable to the armrest.

Anti-Tip Wheels

The anti-tip wheels are designed to give your power chair increased stability on rough surfaces. The anti-tip wheels are preset at the factory for use on smooth surfaces or indoors. If you plan on using your power chair on rough surfaces, it may be necessary to adjust the anti-tip wheels to better suit your needs. The anti- tip wheels may need adjustment if either of the following occur:

νWhen coming to a stop, your power chair tips forward excessively.

νThe anti-tip wheels constantly rub the ground.

NOTE: Make sure that each drive tire has at least 30 psi and the user is seated in the power chair.

WARNING! The higher you raise the anti-tip wheels, the more tendency your power chair has to tilt forward when coming to a stop. You can compensate for this by having your authorized Pride provider make a small adjustment to the pre-programmed deceleration setting in the controller or by moving the seat assembly further to the rear of your power chair.

WARNING! Consult your authorized Pride provider before attempting to change the anti-tip wheel height! Changing the anti-tip wheel height affects handling under deceleration!

SETSCREW

Figure 25. Underside of Armrest

ANTI-TIP

WHEEL

BRACKET

ANTI-TIP

WHEEL

Figure 26. Anti-Tip Wheel

Assembly

To adjust the anti-tip wheels:

1.Remove the anti-tip wheel. See figure 26.

2.Remove the nut and bolt on the anti-tip wheel bracket. See figure 26.

3.Raise or lower the anti-tip wheel.

4.Reinstall the nut and bolt on the anti-tip wheel bracket.

5.Reinstall the wheel.

6.Repeat the same procedure for the other anti-tip wheel.

Jazzy 1133 Owner’s Manual Rev B 03-03

www.pridemobility.com

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Exeter, PA St. Catharines, on F E T Y G U I D E L I N E S N T E N T S N T R O D U C T I O N IntroductionInformation Exchange Pride Owners Club My Authorized Pride Provider IsQuick Reference Information Pre-Ride Safety Check S a F E T YModifications Weight Limitations Tire InflationIncline Information Cornering Information Braking InformationFreewheel Mode Outdoor Driving SurfacesStationary Obstacles Steps, Curbs, etc EMI & RFI Inclement Weather Precautions TransfersPositioning Belts Removable Parts Reaching and BendingBatteries AlcoholFrequently Asked Questions Faqs Where do radio waves come from?I . E M I / R F Are all power chairs susceptible to EMI/RFI? What is the FDA doing about the problem?What should I do if my power chair moves unexpectedly? Jazzy T H E J a Z Z Y 1 1 3Jazzy 1133 Specifications Jazzy 1133 Power Base Assembly Seat Removed Jazzy 1133 Back of Power Base Power Base AssemblyTo engage or disengage the drive motor Manual Freewheel LeversI S a S S E M B L Y Jazzy 1133 Power Base ComponentsSlide the rear battery box off the frame and set aside Pull the footrest up and off the frame and set it aside C O M F O R T a D J U S T M E N T S Comfort AdjustmentsReclining Seat To adjust the seatback angleSeatback Angle Adjustment no seatback release lever Armrest Width AdjustmentTo adjust the SFR length Armrest Angle Adjustment To change the armrest angleFootrest Depth To adjust the footrest depth To adjust the footrest angleTo adjust the ELR length To adjust the ELR angleAnti-Tip Wheels To adjust the anti-tip wheelsController Position To change the controller positionCharging the Batteries To charge the batteries using the onboard chargerI . B a T T E R I E S a N D C H a R G I N G Batteries and ChargingTo charge the batteries using the off-board charger Battery Break-inTo break in new batteries for maximum efficiency How can I get maximum range or distance per charge? Can I use a different battery charger?How does the charger work? How often must I charge the batteries?What type of batteries should I use? Why do my new batteries seem weak?How can I ensure maximum battery life? How should I store my power chair and its batteries?Joystick I I . O P E R a T I O NVSI Controller VSI consistsBattery Condition Meter On/Off KeySpeed/Profile Keys Off-board Charger/Programming Socket Controller ConnectorPin Charger Inhibit Connector Horn KeyFlashing Lights DIAGNOSIS/SOLUTION VSI Error CodesDaily Checks Care and MaintenanceC a R E a N D M a I N T E N a N C E General GuidelinesYearly Checks Cleaning PrecautionsTo check the brakes Monthly ChecksShould your power chair come in contact with water TemperatureBattery Replacement To replace the batteries Jazzy 1133 Rear Battery BoxBattery Layout Label TIRE/WHEEL ReplacementWhen to see Your Authorized Pride Provider for Service Motor BrushesTo inspect or replace the motor brushes P T I O N a L a C C E S S O R I E S W a R R a N T Y Lifetime Limited WarrantyT E S T E S T E S Quality Control

Jazzy1133 specifications

The Pride Mobility Jazzy 1133 is a versatile power chair designed to provide exceptional comfort and mobility to users with limited mobility. This power wheelchair is not only renowned for its sleek design but also for its cutting-edge technology and user-centric features that enhance mobility in a variety of settings.

One of the most notable features of the Jazzy 1133 is its mid-wheel drive design. This allows for a tighter turning radius, making it incredibly maneuverable in indoor spaces, such as homes and shops. The chair is equipped with a powerful motor that provides smooth acceleration and a top speed of approximately 4.5 mph, ensuring users can navigate both indoor and outdoor environments with ease.

Comfort is paramount in the Jazzy 1133, and it comes with a high-back seat that offers luxurious padding and adjustable armrests. The seat height can also be adjusted, accommodating various user needs and preferences. This attention to comfort is essential for users who may need to spend prolonged periods in the chair, as it minimizes the risk of pressure sores and enhances overall user satisfaction.

The Jazzy 1133 features advanced suspension technology, providing a stable ride over different terrains. This means users can traverse grassy areas, sidewalks, and uneven surfaces without compromising comfort or safety. Its robust and durable construction ensures that the chair can withstand daily use while retaining its performance.

In terms of technology, the Jazzy 1133 is equipped with a performance-oriented controller that allows for precise maneuverability. Users can easily navigate their chair with intuitive joystick controls that enable them to move forward, backward, and accommodate various turns. The chair also has programmable settings, allowing users to tailor the chair's performance to their specific needs.

Durability is another hallmark of the Jazzy 1133, featuring strong, puncture-resistant tires that can handle a variety of surfaces. The battery system ensures reliable performance, offering a range of up to 12 miles on a single charge, making it ideal for both short trips and extended outings.

Overall, the Pride Mobility Jazzy 1133 is a thoughtfully designed power wheelchair that combines comfort, technology, and reliability. With its user-friendly features and robust performance, the Jazzy 1133 stands out as a leading choice for individuals seeking a quality mobility solution that meets their varied lifestyle demands.
Top Page Image Contents