Pride Mobility Jazzy 1103 Battery Condition Meter, Speed Control Knob, Controller Connector

Page 29

V I I . O P E R A T I O N

Battery Condition Meter

The battery condition meter is located in front of the joystick. This is a 10-segment illuminated display that indicates that the Pilot is turned on and also gives the battery status, the Pilot status, and the electrical system status.

νRed, yellow, and green lights lit: Battery charged; Pilot and electrical system OK.

νRed and yellow lights lit: Charge battery if possible; Pilot and electrical system OK.

νRed lights only lit or slow flash: Charge battery as soon as possible; Pilot and electrical system OK.

νRapid flash of lights: Indicates a fault in the Pilot or the electrical system. Refer to “Pilot Error Codes.”

νRipple up and down of lights: The joystick was not in the neutral position when the controller was turned on. If you get “ripple up and down of lights”, turn off the controller, allow the joystick to return to the neutral position, then turn on the controller.

NOTE: If you still get “ripple up and down of lights”, contact your authorized Pride Provider.

NOTE: When the batteries approach a discharged state, the first red light will begin to slowly flash, reminding you the batteries need to be charged immediately!

Speed Control Knob

Sets the maximum speed of the power chair: clockwise to increase, counterclockwise to decrease.

NOTE: We recommend that the first few times you operate your power chair, you turn the speed control to the slowest setting until you become familiar with your new power chair.

Off-board Charger/Programming Socket

You may use an off-board charger to charge the power chair batteries through the 3-pin socket located on the front of the Pilot. If you use an off-board charger, the charger current should not exceed 12 amps. Contact your authorized Pride provider for more information.

CAUTION! Only chargers with Neutrik NC3MX plugs should be connected to the offboard charger/programming socket. See your authorized Pride provider for more information.

NOTE: The offboard charger/programming socket may also be used for reprogramming the Pilot. Contact your authorized Pride provider for more information.

Controller Connector

This connects the Pilot to the power chair’s batteries, motors, and motor brakes.

3-pin Charger Inhibit Connector

This connects the Pilot to the onboard battery charger. This connection provides an inhibit that disables the Pilot when the battery charger is on. The charger inhibit connector is coded with colored dots. The dots are positioned so that you align the flat side of the male connector with the flat side of the female connector before making the connection.

CAUTION! Failure to properly align the connectors can result in damage to the Pilot, the charger harness, and the connectors.

Jazzy 1103 Rev L/Feb03

www.pridemobility.com

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Exeter, PA St. Catharines, on F E T Y G U I D E L I N E S N T E N T S Information Exchange N T R O D U C T I O NIntroduction My Authorized Pride Provider Is Pride Owners ClubModifications Pre-Ride Safety CheckS a F E T Y Incline Information Weight LimitationsTire Inflation Cornering Information Braking InformationStationary Obstacles Steps, Curbs, etc Freewheel ModeOutdoor Driving Surfaces EMI & RFI Positioning Belts Inclement Weather PrecautionsBatteries Reaching and BendingAlcohol Removable PartsI . E M I / R F EMI/RFI-FREQUENTLY Asked Questions FaqsWhere do radio waves come from? What should I do if my power chair moves unexpectedly? Are all power chairs susceptible to EMI/RFI?What is the FDA doing about the problem? Jazzy T H E J a Z Z Y 1 1 0Jazzy 1103 Specifications Jazzy 1103 Power Base Shroud Removed Electronics Tray To engage or disengage the drive motors Manual Freewheel LeversTo change the seat height O M F O R T a D J U S T M E N T SSeat Height To change the armrest width Armrest Width AdjustmentFootrest Height Armrest Height AdjustmentFootrest Angle Footrest DepthTo adjust the anti-tip wheel height ANTI-TIP Wheel AdjustmentB a T T E R I E S a N D C H a R G I N G To charge the batteries using the onboard chargerBatteries Charging the BatteriesBattery BREAK-IN To charge the batteries using the off-board chargerCan I use a different battery charger? OFF-BOARD ChargerHow often must I charge the batteries? Battery SpecificationsDaily Use Infrequent UseHow can I ensure maximum battery life? Why do my new batteries seem weak?How should I store my Jazzy and its batteries? What about public transportation?Pilot Controller I . O P E R a T I O NJoystick On/Off ButtonController Connector Battery Condition MeterPin Charger Inhibit Connector Speed Control KnobTrouble Codes Thermal RollbackKeypad I I . O P E R a T I O NVSI Controller Speed/Profile Keys On/Off KeyHorn Key Actuator Key and Actuator Lights for optional equipmentVSI Error Codes TroubleshootingTemperature Routine MaintenanceI I . C a R E a N D M a I N T E N a N C E General GuidelinesWeekly Checks Daily ChecksMonthly Checks Cleaning Instructions TIRE/WHEEL ReplacementYearly Checks StorageTo replace the batteries Battery ReplacementCorrective Maintenance When to see Your Authorized Pride Provider for ServiceMotor Brushes To inspect or replace the motor brushesO P T I O N S a N D a C C E S S O R I E S Power Seat ActuatorPower Seat Switch Power Elevating Seat OperationCane and Crutch Holder Positioning BeltWalker Holder CUP HolderA R R a N T Y Damage caused by Warranty ExclusionsT E S T E S Pride keeps a more detailed report on file at the factory Quality Control Model
Top Page Image Contents