Pride Mobility Jazzy 1103 Actuator Key and Actuator Lights for optional equipment, Horn Key

Page 33

V I I I . O P E R A T I O N

NOTE: We recommend that the first few times you operate your power chair, you set the speed to the slowest setting until you become familiar with your new power chair.

Actuator Key and Actuator Lights (for optional equipment)

Actuator keys and actuator lights are used for optional equipment such as power elevating seats or power elevating leg rests. For specific operation of the actuator keys and actuator lights, contact your authorized Pride provider.

Horn Key

The horn key activates the horn.

Off-board Charger/Programming Socket

You may use an off-board charger to charge the power chair batteries through the 3-pin socket located on the front of the VSI. See figure 15b. If you use and off-board charger, the charger current should not exceed 12 amps. Contact your authorized Pride provider for more information.

CAUTION! Only chargers with Neutrik NC3MX plugs should be connected to the off-board charger/programming socket. See your authorized Pride provider for more information.

NOTE: The socket may also be used for reprogramming the VSI. Contact your authorized Pride provider for more information.

Controller Connector

This connects the VSI to the power chair’s batteries, motors, and motor brakes.

3-pin Charger Inhibit Connector

This connects the VSI to the onboard battery charger. This connection provides an inhibit that disables the VSI when the battery charger is on. The charger inhibit connector is coded with colored dots. The dots are positioned so that you align the flat side of the male connector with the flat side of the female connector before making the connection.

CAUTION! Failure to properly align the connectors can result in damage to the VSI, the charger harness, and the connectors.

Thermal Rollback

The VSI controller is equipped with a thermal rollback circuit. The circuit monitors the temperature of the controller, which roughly translates to motor temperature. In the event that the VSI controller becomes excessively hot (above 140° F), motor current (amperage) is reduced. For every degree above 140° F, the motor current limit is reduced by .55 amps until the VSI controller reaches 158° F, at which time the current output is reduced to zero. This reduces your power chair’s “power,” which could also reduce your power chair’s speed, and allows the electrical components and motors to cool down. When the temperature returns to a safe level, your power chair resumes its normal operation.

Jazzy 1103 Rev L/Feb03

www.pridemobility.com

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Exeter, PA St. Catharines, on F E T Y G U I D E L I N E S N T E N T S N T R O D U C T I O N IntroductionInformation Exchange My Authorized Pride Provider Is Pride Owners ClubPre-Ride Safety Check S a F E T YModifications Weight Limitations Tire InflationIncline Information Cornering Information Braking InformationFreewheel Mode Outdoor Driving SurfacesStationary Obstacles Steps, Curbs, etc EMI & RFI Positioning Belts Inclement Weather PrecautionsBatteries Reaching and BendingAlcohol Removable PartsEMI/RFI-FREQUENTLY Asked Questions Faqs Where do radio waves come from?I . E M I / R F Are all power chairs susceptible to EMI/RFI? What is the FDA doing about the problem?What should I do if my power chair moves unexpectedly? Jazzy T H E J a Z Z Y 1 1 0Jazzy 1103 Specifications Jazzy 1103 Power Base Shroud Removed Electronics Tray To engage or disengage the drive motors Manual Freewheel LeversO M F O R T a D J U S T M E N T S Seat HeightTo change the seat height To change the armrest width Armrest Width AdjustmentFootrest Height Armrest Height AdjustmentFootrest Angle Footrest DepthTo adjust the anti-tip wheel height ANTI-TIP Wheel AdjustmentB a T T E R I E S a N D C H a R G I N G To charge the batteries using the onboard chargerBatteries Charging the BatteriesBattery BREAK-IN To charge the batteries using the off-board chargerCan I use a different battery charger? OFF-BOARD ChargerHow often must I charge the batteries? Battery SpecificationsDaily Use Infrequent UseHow can I ensure maximum battery life? Why do my new batteries seem weak?How should I store my Jazzy and its batteries? What about public transportation?Pilot Controller I . O P E R a T I O NJoystick On/Off ButtonController Connector Battery Condition MeterPin Charger Inhibit Connector Speed Control KnobTrouble Codes Thermal RollbackI I . O P E R a T I O N VSI ControllerKeypad Speed/Profile Keys On/Off KeyHorn Key Actuator Key and Actuator Lights for optional equipmentVSI Error Codes TroubleshootingTemperature Routine MaintenanceI I . C a R E a N D M a I N T E N a N C E General GuidelinesWeekly Checks Daily ChecksMonthly Checks Cleaning Instructions TIRE/WHEEL ReplacementYearly Checks StorageTo replace the batteries Battery ReplacementCorrective Maintenance When to see Your Authorized Pride Provider for ServiceMotor Brushes To inspect or replace the motor brushesO P T I O N S a N D a C C E S S O R I E S Power Seat ActuatorPower Seat Switch Power Elevating Seat OperationCane and Crutch Holder Positioning BeltWalker Holder CUP HolderA R R a N T Y Damage caused by Warranty ExclusionsT E S T E S Pride keeps a more detailed report on file at the factory Quality Control Model
Top Page Image Contents