Pride Mobility INFMANU3351 manual Battery Replacement, To replace the batteries

Page 41

V I I . C A R E A N D M A I N T E N A N C E

Battery Replacement

A battery wiring diagram is printed on a decal located on the power base. See VI. “Batteries and Charging” for correct battery specifications.

MANDATORY! Battery posts, terminals, and related accessories contain lead and lead compounds. Wear goggles and gloves when handling batteries and wash hands after handling.

WARNING! The batteries in your power chair should only be serviced or replaced by an authorized Pride Provider or a qualified technician.

WARNING! Do not replace batteries when seat is occupied.

WARNING! Power chair batteries are heavy. See specifications table. If you are unable to lift that much weight, be sure to get help. Use proper lifting techniques and avoid lifting beyond your capacity.

WARNING! Do not mix old and new batteries. Always replace both batteries at the same time.

PROHIBITED! Keep tools and other metal objects away from the battery terminals. Contact with tools can cause electrical shock.

You may need the following to replace your batteries: metric/standard socket set and ratchet

adjustable wrench

To replace the batteries:

1.Turn off power to the controller.

2.Make sure that the power chair is in drive mode. See figure 11.

3.Remove the rear shroud. See figure 29.

4.Loosen the yellow thumbscrews and remove the side cover.

5.Disconnect the rear battery harness from the power base. See figure 29.

6.Slide the rear battery out of the power base.

7.Slide the front battery rearward.

8.Disconnect the front battery harness from the power base. See figure 29.

9.Slide the front battery out of the power base.

10.Remove the battery harnesses from the old batteries and install them onto the new batteries. Make sure that the hardware is facing the correct direction. See figure 29.

WARNING! Make sure you tighten the fasteners so that the connections are secure.

11.Place the front battery into the power base. Make sure that the terminals are facing the front of the power base.

See figure 29.

12.Connect the front battery harness to the power base.

13.Slide the front battery forward.

14.Place the rear battery onto the power base. Make sure that the terminals are facing the front of the power base.

See figure 29.

15.Connect the rear battery harness to the power base.

16.Reinstall the side cover.

17.Reinstall the rear shroud.

NOTE: When installing the rear shroud, make sure that the controller and power seat harnesses are routed through the notch in the right side of the front cover.

18. Charge the batteries. See VI. “Batteries and Charging.”

Jazzy Select Series

www.pridemobility.com

41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Jazzy Quick Reference Information F E T Y G U I D E L I N E SIII Appendix I SpecificationsN T R O D U C T I O N SafetyPURCHASER’S Agreement Shipping and DeliveryS a F E T Y Product Safety SymbolsS a F E T Y S a F E T Y S a F E T Y Modifications Pre-Ride Safety CheckGeneral Guidelines Incline Information Weight LimitationsTire Inflation Cornering Information Freewheel ModeBraking Information Stationary Obstacles Steps, Curbs, etc Inclement Weather PrecautionsPublic Streets and Roadways Outdoor Driving Surfaces Doors Stairs and EscalatorsElevators Lift System/Elevation ProductsBatteries Positioning BeltsPrescription Drugs/Physical Limitations TransfersElectromagnetic and Radio Frequency Interference EMI/RFI Alcohol/SmokingI . Y O U R P O W E R C H a I R Jazzy Select Series Power ChairJazzy Select Power Base Jazzy Select 6 with Power Seat Electrical Components Jazzy Select 6 with Power Seat Electrical Components To engage or disengage the drive motors Manual Freewheel LeversA S S E M B L Y Initial AssemblySeat Installation Select and Select 6 only To install the power seat Seat Installation Select 6 with Power Seat onlySeat Latch Safety Seat Height Adjustment Select and Select 6 Only Comfort AdjustmentsO M F O R T a D J U S T M E N T S To change the seat heightVR2 6-key Controller and Keypad Seat Height Adjustment Select 6 with Power Seat OnlySeatback Angle Adjustment Manual Recline Seatback AdjustmentArmrest Width Adjustment Armrest Angle AdjustmentTo change the armrest height Armrest Height AdjustmentController Position To extend the controllerFoot Platform Angle Adjustment Foot Platform Height AdjustmentFoot Platform Depth Adjustment Elevating Leg Rests Swing-away FootrestsAnti-Tip Wheels Select Only To adjust the anti-tip wheelsCharging the Batteries B a T T E R I E S a N D C H a R G I N GBatteries and Charging Frequently Asked Questions FAQs Battery Break-inDaily Use Why do my new batteries seem weak?Infrequent Use How can I get maximum range or distance per charge?How should I store my power chair and its batteries? How can I ensure maximum battery life?What about public transportation? What about shipping?Should your power chair come in contact with water Care and MaintenanceTemperature I . C a R E a N D M a I N T E N a N C EWeekly Checks Daily ChecksTo check the brakes Monthly ChecksCleaning and Disinfection Disposal of Your Power ChairWheel Replacement Yearly ChecksJazzy Select Drive Wheel Removal To replace the batteries Battery ReplacementI . C a R E a N D M a I N T E N a N C E Corrective Maintenance When to See Your Authorized Pride Provider for ServiceI I . W a R R a N T Y Implied Warranties Service Checks and Warranty ServiceSpecifications P E N D I X I Specification SJazzy Select Dimensions and Ground Clearance T E S T E S T E S Product Serial # Date InspectedInspector
Top Page Image Contents