Pride Mobility Hurricane owner manual I I . a S S E M B LY a N D D I S a S S E M B LY, Assembly

Page 27
Figure 15. Position the Front and Rear Sections

V I I I . A S S E M B LY A N D D I S A S S E M B LY

No tools are required to assemble or disassemble your Hurricane.Always assemble or disassemble your Hurricane on a level, dry surface with sufficient room for you to work and move around your Scooter. Keep in mind that the disassembled sections of the Hurricane take up more floor space than the assembled Scooter.

ASSEMBLY

1.Place the freewheel lever in drive (down) position.

2.Position the front and rear sections next to each other. See figure 15.

3.Tilt the rear end to a horizontal position and insert the longer tube of the front end into the rear section first; make sure that the locking cam levers are vertically positioned and the locking pins are removed.

4.Slide the two sections of the unit together until the front half reaches its insertion limit.

5.Secure the front and rear sections with ball detent pins. See figure 16.

6.Ensure the tiller is in an upright position.

7. Push the locking cam levers back to their locked (down) position. See figure 17.

8.Clip the front basket onto the front of the tiller.

9.If you removed the utility tray from the rear component, replace the tray by aligning the reusable fasteners on the utility tray with those on the Scooter’s rear component; gently press down on the utility tray to ensure it is secure.

10.Plug the large white 9-pin plastic connector from the front section of the Hurricane into the mating plug found on the control module on the utility tray. The two orange dots present on both plugs should be adjacent to each other and enable quick plug mating. See figure 18.

Figure 16. Secure Sections with

Figure 17. Push the Locking Cam

Figure 18. Plug in the 9-pin

Ball Detent Pins

Levers

Connector

Hurricane

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Ultimate In Style & Performance F E T Y G U I D E L I N E S III N T E N T SP Y R I G H T N T R O D U C T I O N S a F E T Y Safety Precautions68-90 kg 113-136 kg Stone DoorsElevators Ramps and Other InclinesNormal Driving Position Driving SurfacesHurricane Specifications 141 cm 50 cm I . Specification S6SHFLILFDWLRQV D E S C R I P T I O N Control Console AssemblyTiller Adjustment Lever Hazard Light SwitchKey Switch Left and Right Turn Signal ButtonsBattery Condition Meter Speed Adjustment DialHandbrake Lever Light SwitchMPH Switch Power Seat Switch OptionalElectronic Controller Module Onboard Battery ChargerRear Section BatteriesManual Freewheel Lever Motor/Transaxle AssemblyMain Circuit Breaker Anti-Tip Wheels Not shown in photoOptional Accessories Reading Your Battery Voltage A T T E R I E S a N D C H a R G I N GCharging Your Batteries How does the charger work? Frequently Asked Questions FaqsHow can I get maximum range or distance per charge? Why do my new batteries seem weak? How can I ensure maximum battery life? Operating Your Scooter PRE-RIDE Adjustments and ChecksO P E R a T I O N Getting on Your ScooterGetting OFF of Your Scooter Auto Shutoff FeatureI . C O M F O R T a D J U S T M E N T S Tiller Angle AdjustmentSeat Height Adjustment Power Seat Actuator OptionalSeat Rotation Operating Your Power SeatSliding Seat Adjustment Armrest Width AdjustmentHIGH-BACK Seat Headrest Adjustment Armrest Height AdjustmentI I . a S S E M B LY a N D D I S a S S E M B LY AssemblyRotate the seat until it locks into place Disassembly Problem Possible Solutions TroubleshootingTyre Pressure A R E a N D M a I N T E N a N C EService Checks and Warranty Service TWO-YEAR Limited WarrantyONE-YEAR Limited Warranty Not Covered Under Warranty Batteries
Top Page Image Contents