Pride Mobility 1400 owner manual Wheel Replacement, To replace the wheel, Battery Replacement

Page 34

V I I I . C A R E A N D M A I N T E N A N C E

WARNING! Never use any chemicals to clean a vinyl seat, as they may cause the seat to become slippery or dry out and crack. Use soapy water and dry the seat thoroughly.

Wheel Replacement

If your chair is equipped with a solid tire insert, then you must replace the whole wheel assembly. Replacement wheel as- semblies are readily available through an authorized Pride Provider.

WARNING! To avoid possible injury, be sure that the controller’s power is turned off and the Go-Chair is not in freewheel mode before performing this procedure.

To replace the wheel:

1. Turnoffthepowertothecontroller.

2. Set the Go-Chair up on blocks.

3. Removethedrivewheelnutfromthewheelhub.Seefigure24.

4. Pullthewheelofftheaxle.

5. Slide the new wheel back onto the shaft. Make sure that the keyisintheaxleslot.

6.Reinstallthedrivewheelnutontothewheelhubandtighten.

7.Remove the Go-Chair from the blocks.

Battery Replacement

Figure 24. Go-Chair Drive Wheel

A battery wiring diagram is printed on a decal located on the front battery tray. See the Specifications Table for correct battery specifications.

WARNING! Prevent injury. Do not replace battery when seat is occupied.

WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds. Wear goggles and gloves when handling batteries and wash hands after handling.

WARNING! Go-Chair batteries are heavy. See specifications table. If you are unable to lift that much weight, be sure to get help. Lifting beyond your capacity can result in personal injury.

To replace the batteries:

1.Remove the battery box from the Go-Chair.

2.Turn the pack upside down.

3.Remove all screws that hold the battery box halves together. See figure 25.

4.Flip the battery box back over so the handle is up and remove the lid.

5.Remove the red (+) positive and black (-) negative battery leads from each battery.

6.Remove the batteries.

7.Put the new battery or batteries back into the battery box (battery terminals up).

8.Reconnect the two (2) battery leads to the battery terminals. Make sure the red lead is connected to the (+) positive terminal and the black lead is connected to the (-) negative terminal.

9.Replace the lid and carefully flip the battery box over so the handle is down.

10.Replace and tighten all the screws that hold the battery box together.

11.Reinstall the battery box back onto the Go-Chair.

34

www.pridemobility.com

Go-Chair

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Exeter, PA St. Catharines, on F E T Y G U I D E L I N E S N T E N T S IIIPURCHASER’S Agreement SafetyN T R O D U C T I O N Internet and Private PurchasesPride Owners Club Quick Reference InformationProduct Safety Symbols S a F E T YS a F E T Y Pre-Ride Safety Check ModificationsWeight Limitations Incline InformationBraking Information Public Streets and Roadways Freewheel ModeCornering Information Stationary Obstacles Steps, Curbs, etc Outdoor Driving SurfacesStairs and Escalators Elevators TransfersDoors Lift/Elevation ProductsPositioning Belts Reaching and Bending Inclement Weather PrecautionsMotor Vehicle Transport BatteriesAlcohol Electromagnetic and Radio Frequency Interference EMI/RFII . Y O U R G O C H a I R GO-CHAIRGO-CHAIRSPECIFICATIONS Go-Chair Power Base Electrical ComponentsTo engage or disengage the drive system Manual Freewheel LeversANTI-TIP Wheels Initial Assembly A S S E M B L Y / D I S a S S E M B L YDisassembly Seat InstallationTo install the seat AssemblyToggle Latch Closed O M F O R T a D J U S T M E N T S Comfort AdjustmentsSeat Height Adjustment Quick Release FastenersController Position To adjust the foot platform depthFoot Platform Depth To change the controller positionBatteries and Charging B a T T E R I E S a N D C H a R G I N GCharging the Batteries Battery Break-in Frequently Asked Questions FAQsHow can I get maximum range or distance per charge? Why do my new batteries seem weak?How can I ensure maximum battery life? What type of batteries should I use?What about public transportation? How should I store my Go-Chair and its batteries?What about shipping? Joystick I . O P E R a T I O NVSI Controller KeypadSpeed Keys Battery Condition MeterOn/Off Key Horn KeyLocking/Unlocking the VSI Controller ConnectorSleep Mode Off-board Charger SocketVSI Error Codes Thermal RollbackI I . C a R E a N D M a I N T E N a N C E Care and MaintenanceTemperature Should your Go-Chair come in contact with waterWeekly Checks Cleaning InstructionsDaily Checks Monthly ChecksTo replace the wheel Wheel ReplacementBattery Replacement To replace the batteriesWhen to See An Authorized Pride Provider for Service Corrective MaintenanceW a R R a N T Y Service Checks and Warranty Service Implied WarrantiesT E S Quality Control Go-Chair Pride keeps a more detailed report on file at the factory
Related manuals
Manual 50 pages 49.48 Kb
Top Page Image Contents