26 | X . S e t - U p & A d j u s t m e n t s | ||
A. | WHEELS |
|
|
1. | Installation |
|
|
| a. Depress the |
|
|
| axle.(Fig. 3) |
|
|
| b. Slide through wheel hub and into axle sleeve |
|
|
| until it locks. |
|
|
| c. The axle is not secured until the outside |
|
|
|
| ||
| extended position. | Button |
|
| d. The ball bearing on the opposite end of the | Figure 3 |
|
| axle must be fully visible beyond the end of |
| |
|
|
| |
| the axle sleeve. |
|
|
B. REMOVABLE |
|
| |
1 |
| ||
1. | Height Adjustment | 2 | 4 |
| a. Release the upper securing lever. | ||
| 5 | ||
|
| ||
| b. Slide armpad up or down to | 3 | |
|
| ||
| desired height. |
|
|
| c. Return lever to locked position. |
|
|
2. | Removing Armrest |
|
|
| a. Depress the release latch, and lift the armrest up. |
|
|
b. To return armrest to operating position, drop | Removable | ||
Armrest Key | |||
armrest into receiver, and pull lever back. Make | |||
1. | Armrest Pad | ||
sure the armrest is locked in place. | |||
2. | Upper Securing Lever | ||
C. | |||
3. | Release Latch | ||
FOOTRESTS (60º, 70º, 70ºV OR 90º) | |||
4. | Armrest Panel | ||
1. Installation (Fig. 5) | |||
5. | Rear Receiver | ||
|
| a. Place |
|
| on front frame tube with the footrest facing out- |
|
| ward from the frame. (Fig. |
|
| b. Rotate the footrest inward until it locks into | A |
| place on locking bolt. (Fig. | |
|
| |
2. | Removal |
|
| a. To remove footrest, push release latch toward the |
|
| frame. |
|
| b. Rotate footrest outward and lift. |
|
|
| B |
|
| Figure 5 |
X . S e t - U p & A d j u s t m e n t s | 27 | |
D. FIXED FRONT FOOTRESTS |
| |
1. Adjustment (Fig. 6) |
| |
a. Remove mounting bolts on the top of each |
| |
extension tube. |
| |
b. Make sure the inserts remain in place. |
| |
c. Slide footrest tube into front frame tube to |
| |
desired height. |
| |
d. Line up holes and replace the bolt on the outside |
| |
through frame, footrest and insert. |
| |
e. Follow same procedure on opposite side. | Figure 6 | |
f. Align footrests to desired inward/outward rota- | ||
| ||
tional position and tighten firmly. |
|
E. BACKREST
1.Height Adjustment (Fig. 7)
a.Remove the backrest upholstery from the frame.
b.You will see the backrest tube which telescopes
into the frame and is secured by a screw on the side of the frame.
c. There are holes 1 1/8 inch apart from which you may choose to set the back height.
d. Remove the two backrest bolts from the rear Figure 7 frame tubes.
e. After selecting the proper height, insert bolt through frame and backrest tube.
f. Attach upholstery tab to bolt and tighten nut and bolt assembly.
g. Insert nylon tie through upholstery grommets. Tighten and cut off excess nylon tie.
930457 Rev. A | 930457 Rev. A |