REPOSITIONING THE PENDANT HAND CONTROL (FIGURE 2)
NOTE: Refer to the GENERAL WARNINGS in the SAFETY SUMMARY of this Instruction Sheet.
NOTE: This procedure should only be performed by a qualified technician.
1.Place the chair into the seated position.
2.Unplug the motor power cord from the wall.
3.Remove the screws and cable clamps securing the pendant cable to the underside of the armrest.
4.Remove the screw and cable clamp securing the pendant cable to the back of the chair.
5.Roll the chair forward onto the ottoman and the front of the seat back.
6.Plug the motor power cord into the wall.
7.Press the pendant button in the recline direction slightly to produce sufficient slack in the flap of fabric to thread the pendant in through the flap.
8.Press the pendant button in the lift direction until the lift mechanism is fully raised.
9.Unplug the chair power cord from the wall.
10.Remove the screw and cable clamp from the side of the rear corner of the chair.
11.Remove the screw and cable clamp from the middle of the side of the chair.
12.Remove the cable tie securing the pendant cable to the lift frame.
NOTE: Do not remove the cable tie securing the pen- dant cable to the motor.
13.Pull the pendant cable to a spot
14.Securethependantcabletotheliftframewithacabletieat the point closest to the cable as shown in DETAIL "B" of FIGURE 2.
NOTE: There should be minimal slack in the cable between the motor and lift frame.
15.Secure the pendant cable to the middle of the side of the chair with a screw and cable clamp. As shown in DETAIL "B" of FIGURE 2.
NOTE: There should be minimal slack in the cable between the lift frame and cable clamp.
16.Pull the pendant cable tight along the side of the chair to the rear corner of the chair.
17.Secure the pendant cable to the side of the rear cor- ner with no slack in the cable. As shown in DETAIL "B" of FIGURE 2.
18. Plug the chair power cord into the wall.
WARNING
DO NOT let the power cord get pinched, cut or trapped by the lift frame. Other- wise injury or damage may result.
19.Press the pendant button in the recline direction until the lift mechanism returns to the seating position and just makes contact with the wood chair frame.
WARNING
DO NOT let the pendant cable get pinched, cut or trapped by the lift frame. Otherwise injury or damage may result.
20.Press the pendant button in the recline direction to pro- duce sufficient slack in the rear flap of fabric to thread the pendant back out through the flap.
21.Unplug the chair power cord from the wall.
22.Return the chair back onto all four (4) feet.
23.Pullthependantcabletightandsecurethependantcable to the rear of the chair with a screw and cable clamp.
24.Perform one (1) of the following:
A.Murphy, Fairview, and Woodbriar models- proceed to STEP 25.
B.Stanford, Bellaire, Manchester, and Jamestown models - tightly pull the pendant cable to the bend in the armrest. Secure the pendant cable under the bend in the armrest with a screw and cable clamp.
C.New Yorker model - tightly pull the pendant cable to the back end of the armrest. Secure the pen- dant cable under the back end of the armrest with a screw and cable clamp.
25.Secure the pendant cable to the outer side of the chair immediately under the armrest half way be- tween the front of the armrest and the seat back according to following.
A.Murphy, Fairview, Stanford models - the screw must be placed vertically up into the underside of the armrest as shown in FIGURE 2.
B.Woodbriar model - the screw must be placed vertically down into the frame of the chair asshown in FIGURE 2.
C.New Yorker, Bellaire, Manchester, Jamestown models - the screw must be placed horizontally into the side of the chair as shown in FIGURE 2.
NOTE: Pull the pendant cable tightly to minimize slack when securing the cable clamp.
NOTE: Be sure to drive the screws into solid wood, away from edges.
3