DIAGNOSTIC/HELP Code Tables, Help Codes Listing | Maytag 16010061

Section 3: DIAGNOSTIC/HELP CODE TABLES.

HELP CODES LISTING:

	Help	Description	Trigger	Action to be Taken
	Code	Description	Trigger	Action to be Taken
	Code
	01	Plaster Unbalance	Unbalance load	Informative only; non-critical condition
		Load Detected.	condition existed
			during initial ramp up
			or spin cycle.
			Resulted in
			redistribution cycle.
	02	Reset Seen	Electrical noise	Identify where specifically in the cycle
			detected by machine	this occurred, to aid in identifying which
			control board.	components may have been initially
				actuated. Check for loose connections
				of these components and correct if
				necessary. If random, suspect incoming
				power supply to washer.

	03-06	(Not Used)

	07	Slow Drain	Low water level	Check for restricted drain system,
			contacts of pressure	kinked/plugged drain hose or pump.
			switch not seen as	Check pump for proper function. May
			resetting at end of	see diagnostic code 01.
			drain cycle.

	08	One locked rotor	During startup, the	Informative only; non-critical condition.
			Spinner did not reach
			10 rpm within 2 sec.
			(During Wash/Tumble)

	09	Fill hoses are	Water valve	Informative only; (LED washer only)
		reversed	thermistor readings
			are contrary to what
			is being demanded
			by washer control
			board.

	10	Locked rotor	Locked rotor	Informative only; non-critical condition.
		condition during a	condition during a
		spin	spin.

	11	(Not used)

	12	(Not used)

	13	Low Speed	Opening of unbalance	Informative only; not-critical condition.
		Unbalance	switches at speed
		Detected.	<500 rpm

	14	(Not used)

	15	(Not Used)

16010486 (16008373-05)	Section 3. Teardown & Wiring Information	3-1
16010486 (16008373-05)	Section 3. Teardown & Wiring Information
Revised 2/01	©2001 Maytag Appliances Sales Company

Image 131

Maytag 16010061 service manual DIAGNOSTIC/HELP Code Tables, Help Codes Listing

Contents

Washer Safety Precautions MAH3000 Introduction General N T E N T S Iii Section Motor General Information Installation Grounding Polarity Checks Specifications Washer Controls Series 17 & Later Input Definitions Water Valve Outputs Output Definitions Torque Output Cycle Sequence Definitions Miscellaneous Push-To-Start Relay Operation Cycle Review General Component Exploded View Electrical Test Equipment Electrical Components & Testing O u n d e d C o m p o n e n t s Timer & Console Switches Key 0 = Input Signal Not Asserted Machine Control C HIN E FU N Ctio N N T R O L L T a GE IM ER A R D Drive Motor Motor & Motor Control Test Motor Windings Check Disconnect power to the washer prior to testing Tachometer Circuit Diagnostics Unbalance Control System Tub Displacement Switch Inertial Unbalance Switch Maytag Corporation Shuts OFF When Push-To-Start Button Re- leased Troubleshooting Temperature Inputs Door Leaks Troubleshooting Troubleshooting Troubleshooting Troubleshooting Troubleshooting Troubleshooting Troubleshooting Troubleshooting 3 1 Troubleshooting Facia. Press Timer knob onto the timer Shaft Washer Wattages Miscellaneous InformationEnergy Usage M O V a L Console Vertical Switches Push Button Timer Removal Maytag Corporation Door Assembly & Hinges Cabinet Assembly Front Panel Cabinet Vibration Absorber Door Lock Mechanism TOP Cover Troubleshooting Front Shroud Assembly Hinge Removal Access Panel Maytag Corporation Water Valve WATER-CARRYING Components AIR Dome Hose Water Level Pressure Switch REPLACEMENT/ROUTING Dispenser Assembly Front Water Flume Injector Pump Assembly Pump Accessory Kit Drain Hose Reverse the previous steps for replacement Maytag Corporation Baffles Door Boot Outer TUB Cover Replacement Spin Basket Assembly w/BALANCE Ring Profile Washer Spinner Support Locking Nut Drive Pulley Spinner TUB Support Seal System Bearings Outer TUB AssemblyCounter Weights Inertial Unbalance Switch Strut Assembly Outer Tub Switch TUB Displacement Switch Maytag Corporation M O V a L Motor Drive System Machine Control Motor Control Motor Drive Sysytem Electrical Schematics & Timer I N F O R M a T I O N Timer Chart Prior to Series Electrical Schematic Series Timer Chart Series Electrical Schematic Series Timer Chart Series Electrical Schematic Series T E S Introduction Contents Electrical MAH4000/MAH5500A Control Facia Specifications Series 10 MAH4000 only Series 11 & Later Basic Machine OperationWasher Controls Overview Cycle Review Cycle Times Suds detection during stain cycle General overview of Stain Cycle General Component Exploded View Electrical Information TERMINAL/WIRE Water Carrying Components Operation Disconnect power and water to the machine Removal Disconnect power and water to the washer See -11 16010199 Revised 7/00 Maytag Appliances Sales Company Wiring Information Series 10 Schematic MAH4000 only Series 11 MAH4000 and MAH5500 Series 10 Timer Chart MAH4000 Series 11 Timer Chart MAH4000 & MAH5500A 16008373-05 Maytag Models covered in this manual supplement MAH5500B MAH7500A 16010486 Revised 02/01 Maytag Appliances Sales Company MAH5500B Control Facia MAH7500 Control Facia SpecificationsGeneral Information General Flow Of a Complete Wash Cycle Number of Rinses Cycle SequencesWash Time Tumble Wash Selections Tumbling Time Rinse Tumble Times Spin Speed Drain Pump Input Water TemperatureOption Selected ON/OFF Sequence of Pump During Spin Cycle Basic Control Board Philosophy for Both Washers Features of MAH5500B LED Washer User Interface Options Mode Display Characteristics Input Modifications Defined Pressure Switch InputTemperature Sensor Input Door Lock Switch Input Door LOCK/UNLOCK Solenoid Output Output Modifications DefinedSTART/PAUSE Input Tach Input Water Valve Outputs Main Wash Target TemperaturesCycle Sequence Definitions Suds Detection Bleach DispenseRedistribution Door Lock Operation MiscellaneousDoor Lock Philosophy MAH7500A Power LOSS/FAILURESpecial Features Advertising Mode LCD Washer Service ModeLED Washer Fast Time Down Test Service Mode TableLED Washer Special Tests Quick Service Cycle Board Output Test Accessing The Help CodesBoard Input Test Help Codes Clearing the Help Codes Accessing Diagnostic CodesClearing Diagnostic Code List Number of Cycles Since Code Assigned User Interface Tests Accessing Service ModeService Tests LCD Washer During a cycle Service Cycle Detection System Check DIAGNOSTIC/HELP CodesExit diagnostic/help codes Return to Help Codes Listing DIAGNOSTIC/HELP Code Tables Help Description Trigger Action to be Taken Help Description Trigger Action to be Taken Diag Description Trigger Action to be Taken Diagnostic Codes Listing Diag Description Trigger Action to be Taken Diag Description Trigger Action to be Taken Component Identification & Location General Component Exploded View Glossary of Terms Page Page LCD Model Electrical TestsFabric Softner Bleach Cold Hot Thermistor Coil Water Valve LED Model Door Lock Mechanism Machine Control INPUT/OUTPUT Voltages LCD Washer Membrane Pad Checks Motor Control Board Removal Drive MotorMotor Control Board Drip Shield Removal Motor & Motor Control Test Motor PhasesMotor Drive System Test Machine Control Board Output Test Heater Will Not Turn On Heater Assembly Thermistor Temperature Chart LCD Model LED Model Teardown & Wiring InformationConsole Removal Microprocessor Board Removal Door Latch Hoop Cabinet AssemblyConsole Cover Plug Door Lock Mechanism Water System Components Removal Discontinue power and water to the machinePressure Switch Removal Pump AssemblyHeater Assembly Reinstallation Sump Cover Thermistor Removal MAH5500B MAH7500 Maytag Appliances Sales Company