Tanita BC-418MA instruction manual Setting of Clothes Weight

Page 10

GB

 

kg

P T

 

MALE

STABILIZED

FEMALE

cm / ft.in

ATHLETIC

AGE

STEP ON

% FAT

9. Taking Measurement.

Step on the weighing platform in bare feet. Make sure heels are placed on the posterior electrodes, and the front part of the feet are in contact with the anterior electrodes.

10.Measure the Impedance.

When the grips are grasped with both hands, will appear at the bottom of the display and the impedance measurement will begin.

W Weight Only Function

 

 

 

 

GB

 

 

 

 

 

 

 

kg

1. After turning on the unit, press the [

] key.

P T

 

After a momentary display check, “0.0” will appear

MALE

STABILIZED

on the LCD. If measuring units need to be changed,

FEMALE

cm / ft.in

do so at this time by pressing the [

]key.

ATHLETIC

AGE

An arrow on the LCD will follow the selection of

STEP ON

% FAT

weighing units.

 

 

 

 

 

 

 

 

 

The marks will disappear one by one during the measurement; after five full cycles, the measurement will be complete.

mGrab the grips (two locations) only after the body

weight figure on the display has stabilized.

Do not step off the Weighting Platform until

the “

” symbols disappear completely.

In cases when measurements of the body fat ratio

or the quantity of fat are abnormally small or the

error message (E01) is shown on the display, the

probable reason is that the soles of the feet and the

electrodes are not in full contact. Make sure you

step on the Weighing Platform so there is contact

between the electrodes and the soles of your feet.

If the problem is not solved this way, it is possible

that the soles of the feet have calluses and the

resistance is too great. Therefore, place about 0.5

ml of water on each of the four electrodes where

the feet touch before measurement.

 

kg

P T

 

MALE

STABILIZED

FEMALE

cm / ft.in

ATHLETIC

AGE

STEP ON

% FAT

 

kg

P T

 

MALE

STABILIZED

FEMALE

cm / ft.in

ATHLETIC

AGE

STEP ON

% FAT

2. Weight Measurement.

Step on the weighing platform. Weight will be displayed on the LCD.

3.When measuring is complete, press the [ ] key to turn off the power.

mNo printer is available when measuring weight only.

If body composition analysis is desired, turn

the unit off and then on, using the [ ] key.

Important Note: There is no automatic weight lock function.

 

kg

P T

 

MALE

STABILIZED

FEMALE

cm / ft.in

ATHLETIC

AGE

11.Measurement Is Completed.

Once the body weight and impedance measurements have been completed, the overall body fat percentage will be

WSetting of Clothes Weight

STEP ON

% FAT

Left arm

L

R

Right arm

Left leg

L

R

Right leg

 

 

 

 

Trunk

 

shown at the bottom of the display and a buzzer will sound. If the printer is ON, the measurement results will be printed out.

* With regard to the measurement result, please refer to P. 22.

If the printer is OFF, the measurement results (predicted muscle mass, fat mass, and body fat percentage) for each body part can be displayed using the ten-key pad.

Select the number of the desired body part on the ten-key pad.

[4]:

Left arm

[6]:

Right ar

[0]:

Left leg

[ . ]:

Right leg

[5] and [2]:

Trunk

*See page 13 for details on printer settings. Step off the Weighing Platform.

P T

~

 

kg

P T

 

MALE

STABILIZED

FEMALE

cm / ft.in

ATHLETIC

AGE

STEP ON

% FAT

 

kg

P T

 

MALE

STABILIZED

FEMALE

cm / ft.in

ATHLETIC

AGE

STEP ON

% FAT

1. Press the [ P T ] key.

The arrow next to P T t will flash.

2. Enter the clothes weight.

Example: If the clothes weight is 2.0 kg, press [2], [.] and then [0].

*When you want to correct an entry, press the [ ] key and enter the data again.

 

kg

P T

 

MALE

STABILIZED

FEMALE

cm / ft.in

ATHLETIC

AGE

STEP ON

% FAT

12.When You Continue to Measure.

After printing is completed, go back to step 3. Measure by entering the data in the same procedure.

13.Finish Measurement.

Press the [ ] key and turn off the power.

P T

 

kg

P T

 

MALE

STABILIZED

FEMALE

cm / ft.in

ATHLETIC

AGE

STEP ON

% FAT

3. Finalizing the setting

Press the [

P

T

] key to finalize the clothes weight.

The finalized clothes weight is displayed with a minus, an arrow next to P T t lights up, and it becomes possible to measure your weight.

20

21

Image 10
Contents Body Composition Analyzer BC-418MA Usage Conditions Safety NotesPower Source Storage ConditionsProduct Assembly and Components Membrane Switch Assembly InstructionsDigital display Preparation for Use Loading the Printer Paper RollMode Selection Setting the Original Mode N TStandard Athletic Operating Instructions Body Composition AnalysisSetting of Clothes Weight Based on NIH/WHO BMI Guidelines Explanation of the Print OutBody Fat Ranges for Standard Adults AgeClearing Paper Jams Components of the Printer Unit Clearing Paper JamsSpecifications TroubleshootingProblem List Signal lines and connection methods(1).Output data items Transmission data(2).Output data format Error Codes Switching to Remote ModeControl Commands Transmission DataExample of Use Set tare weightSet gender During measurement ResettingMeasurement finished Current Body impedance measurement methodsVoltage Intra-day fluctuations cyclic activity within a single day Causes of errors in impedance measurementsIntra-day fluctuations Weight Intra-day fluctuations Impedance valueNew Regression Formula for Basal Metabolic Rate BMR FFM vs REE Weight vs REEGB 2 Inter-day changes Intra-day fluctuations %FATProduct specifications REE→BMR